manualshive.com logo in svg

Toshiba TC-net 100, Instruction Manual

Share
Download
Toshiba TC-net 100 Instruction Manual Download Page 132

10. RAS function 

 

124 

"Test WDT Timeout Setting Error!! Write= XXX Read= YYY"    --- Writing 
abnormality of setting value 
"Test WDT Counter Value Error!! Write= XXX Count= ZZZ"    --- Abnormality of 
count value 

(h) Show that operation of WDT function is normal. 

If cannot judge to CPU load became low and was stable, or judge to WDT function 
was wrong, following log is output 
"Floating Wait Time is Over. (XX [sec])"    --- Show that Floarting wait time passed. 

(i) Show that started WDT function. 
 

When (e) and (f) are recorded in log, have to coordinate a value of "Fixed wait time" 

(ScanContMoniWaitTime) parameter. 
By the example mentioned above, progress time from (c) to (f) recorded last is 66 seconds. 
Please set "Fixed wait time" in a big value than this time. By this, "WDT abnormality 
detection" does not occur. 
When these adjustment is difficult or log of (e) and (f) is sometimes recorded after passed 
of "ScanContMoniWaitTime", please set WDT function for disable. 

 
(3) Power supply monitor function of own station 

This is a function when used TC-net100(JTNI PCI Express Card) or TC-net1G (JTGI). 
OPC server enables "Power supply monitor function" of JTNI/JTGI of own  node. 
When JTNI/JTGI of own node detects abnormality of the power supply voltage of PCI 
bus card, JTNI/JTGI  leave TC-net. 

When OPC server of own node detects "JTNI/JTGI  leave TC-net" by this, dual states 
switch over to PRE-ONLINE mode. 
If OPC Server is dual system, child node backs up this node. 
Default setting of this function is enabled. 
About a way to disable this function, please refer to 7.1 How to set the environment for 
OPC Server "Change of enable or disable of power supply monitor function of own 

station". 

 

(4) Log related to RAS function 

Read register of JTGI periodically and output log related to RAS function. 
This log related to RAS function, please see log file "TCnetScanCtrl.log". 
In log file, the following states are output. 

 

JTNI/JTGI Status : PowerMonitor Enable.         --- Power supply monitor function : Enable 
JTNI/JTGI Status : PowerMonitor Disable.        --- Power supply monitor function : Disable 
JTNI/JTGI Status : PowerMonitor Status ON.   --- Power supply status : Abnormal 
JTNI/JTGI Status : PowerMonitor Status OFF.  --- Power supply status : Normal 
JTNI/JTGI Status : ScanContMonitor(WDT) Enable. Timeout=XXXX [ms] 
                                                                                                   --- WDT function : Enable 
JTNI/JTGI Status : ScanContMonitor(WDT) Disable.          --- WDT function : Disable 
JTNI/JTGI Status : ScanContMonitor(WDT) Status ON.      --- WDT status : Abnormal 

Summary of Contents for TC-net 100







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands