background image

 

 

© Toshiba International Corporation 2021   www.toshiba.com/tic   Email: [email protected]   (855) 803-7089   13131 West Little York Road, Houston, TX

 

STEP

  

A

 

Startup Checklist 

Voltage

 

□ 

Verify voltages

 

Line voltage = ±10% of drive rating  –  DC bus = Line voltage * 1.414  –  Control voltage = 24 VDC

 

 

 

 

 

 

 

 

 

 

 

SW1 Switch  –

  Move to Sink or Source, otherwise 

pra

 will blink on the keypad. 

 Sink   

 Source

   

 

Motor Rotation

  –  Run the drive at 5 Hz with the keypad (default setting). If incorrect, swap two of the   

output leads (T1, T2 or T3) and retest rotation. 

□ 

Verify motor rotates in the correct direction 

 

 

Blower/Cooling Fan(s) Check

   

□ 

Verify fans operate and air flows in correct direction (bottom to top)

 

 

Analog Inputs

  –  Verify polarity. Scaling can be adjusted with parameters F201 to F221.

 

 VIC (4-20mA) 

 VIA (0-10VDC) 

 VIB (-10 to +10VDC) 

      

 

Parameter 

 Measured Value 

L1 – L2  

 

L1 – L3  

 

L2 – L3  

 

L1 – GND  

 

L2 – GND  

 

L3 – GND  

 

DC Bus (PA/+ – PC/-)  

 

Control Voltage (P24 – CC)  

 

Summary of Contents for S15







Reviews: