
In
troducti
on
Connecti
o
ns
Bas
ic Setup
P
layback
Ed
iti
n
g
V
CR Fu
ncti
on
s
O
th
ers
Fu
nc
ti
on
Set
u
p
Recordi
n
g
85
EN
5. Audio Out
Set the digital audio output.
(Follow steps 1 to 4 on page 83 as left.)
Select “Audio Out” using
[Cursor
U
/
D
], then press [ENTER].
Menu window will appear.
Select a setting using
[Cursor
U
/
D
], then press [ENTER].
Proceed with either of the following steps.
PCM (Default: 48kHz)
Select a setting using
[Cursor
L
/
P
], then press [ENTER].
Your setting is activated.
48kHz: If your amplifier / decoder is NOT compatible
with 96 kHz PCM, select “48kHz”. Sound
recorded at 96 kHz is down sampled to
48 kHz.
96kHz: If your amplifier / decoder is compatible with
96 kHz PCM, select “96kHz”. Sound is
sampled at 96 kHz.
Note
When playing back disc with copyright protection:
• Even if you select “96kHz”, the sound will be down
sampled at 48 kHz.
Dolby Digital (Default: Stream)
Select a setting using
[Cursor
L
/
P
], then press [ENTER].
Your setting is activated.
PCM:
Converts the Dolby Digital into PCM
(2 channel).
If your amplifier / decoder is NOT compatible
with Dolby Digital, set to “PCM”.
Stream: Outputs Dolby Digital signals.
If your amplifier / decoder is compatible with
Dolby Digital, set to “Stream”.
Hint
When playing back a DVD-RW disc recorded in VR
mode:
• If the audio source on a disc is in Dolby Digital
format, set “Dolby Digital” to “PCM” so that you can
switch to main audio (L), sub audio (R), or a
combination of both (L / R) using your amplifier /
decoder.
MPEG (Default: PCM)
Select a setting using
[Cursor
L
/
P
], then press [ENTER].
Your setting is activated.
PCM:
Converts MPEG into PCM.
If your amplifier / decoder is NOT compatible
with MPEG, set to “PCM”.
Stream: Outputs MPEG Audio signals.
If your amplifier / decoder is compatible with
MPEG, set to “Stream”.
DTS (Default: On)
Select a setting using
[Cursor
L
/
P
], then press [ENTER].
Your setting is activated.
On: Outputs DTS signals.
If your amplifier / decoder is compatible with
DTS, set to “On”.
Off: No DTS signal is output.
If your amplifier / decoder is NOT compatible
with DTS, set to “Off”.
Dynamic Range Control (Default: On)
Set to “On” to make the dynamic range narrower.
Select a setting using
[Cursor
L
/
P
], then press [ENTER].
Your setting is activated.
The Dynamic Range Control function is effective
only with analogue audio connection.
Fast Forward with Audio (Default: Off)
Set to “On” to output the sound during DVD playback
at x1.5 fast forward.
Select a setting using
[Cursor
L
/
P
], then press [ENTER].
Your setting is activated.
Audio Out
PCM
MPEG
DTS
Dynamic Range Control
Fast Forward with Audio
Dolby Digital
Dolby Digital
Dolby Digital
48kHz
48kHz
PCM
PCM
96kHz
96kHz
PCM
Dolby Digital
Stream
Stream
MPEG
PCM
Stream
On
On
Off
Off
DTS
DTS
DTS
DTS
On
On
Dynamic Range Control
Dynamic Range Control
Off
Off
Dolby Digital
DTS
On
Fast Forward with Audio
Off
E439BBD_EN.book Page 85 Wednesday, May 31, 2006 4:01 PM