Toshiba RAS-300ASG Owners And Installation Manual Download Page 33

Page: 33 / 35

TROUBLESHOOTING

Trouble

Check Points

Action

Unit dose not

operate

Check that the power cord is plugged into the wall outlet.

Insert the power cord into the wall outlet.

Has the circuit breaker tripped or has the fuse blown?

Reset the circuit breaker or replace the fuse with the specified
replacement fuse.

Has there been a power failure?

Restart operation when power is resumed.

Does the "UNIT ON" lamp flash on and off?

Call your service representative.

Is the voltage too low?

Confirm the available voltage.

Cooling is

abnormally low

Is the filter blocked with dust?

Clean the air filter.

Has the temperature been set properly?

Check and reset it if necessary.

Are the windows or doors open?

Close the windows and doors.

Is anything obstructing the outdoor unit?

Remove the obstruction.

Is the fan speed too low?

Change the fan speed selection.

Is the operation mode FAN or AUTO?

Change to cooling operation or reset the temperature.

Heating is

abnormally low

Is the filter blocked with dust?

Clean the air filter.

Has the temperature been set too low?

Check and reset it if necessary.

Are the windows or doors open?

Close the windows and doors.

Is anything obstructing the outdoor unit?

Remove the obstruction.

Unit stops during

operation

Is the OFF timer operating?

Restart operation.

Has the room temperature reached the set temperature?

Normal operation.

If the above actions do not correct the operation, consult the dealer from whom you bought the unit.

Summary of Contents for RAS-300ASG




































Search results

Summary of Contents for RAS-300ASG

Reviews:

Related manuals for RAS-300ASG

Brands by name

Popular brands

Toshiba RAS-300ASG, Owners And Installation Manual

Search results

Summary of Contents for RAS-300ASG

Reviews:

Related manuals for RAS-300ASG

Brands by name

Popular brands