PRESET OPERATION
14
Set your preferred operation for future use. The setting will be memorized by the
unit for future operation (except air
fl
ow direction).
1. Select your preferred operation.
2. Press and hold
PRESET
for 3 seconds to memorize the setting. The
P
mark
displays.
3.
Press
PRESET
: Operate the preset operation.
AUTO RESTART OPERATION
15
To automatically restart the air conditioner after the power failure (Power of the
unit must be on.)
Setting
1. Press and hold the RESET button on the indoor unit for 3 seconds to set
the operation. (3 beep sound and OPERATION lamp blink 5 time/sec for 5
seconds)
• Do not operate ON timer and OFF timer.
2. Press and hold the RESET button on the indoor unit for 3 seconds to cancel
the operation. (3 beep sound but OPERATION lamp does not blink)
To operate at super low fan speed for quiet operation (except in DRY mode)
Press
QUIET
: Start and stop the operation.
Note:
Under certain conditions, QUIET operation may not provide adequate
cooling due to low sound features.
QUIET OPERATION
16
For comfortable sleep, automatically control air
fl
ow and automatically turn OFF.
Press
COMFORT
SLEEP
: Select 1, 3, 5 or 9 hrs for OFF timer operation.
Note:
The cooling operation, the set temperature will increase automatically
1 degree/hour for 2 hours (maximum 2 degrees increase).
COMFORT SLEEP OPERATION
17
OPERATION AND PERFORMANCE
21
1. Three-minute protection feature: To prevent the unit from being activated for
3 minutes when suddenly restarted or switched to ON.
2. Some minor cracking sound may occur when unit operating. This is normal
because the cracking sound may be caused by expansion/contraction of
plastic.
Air conditioner operating conditions
Temp.
Operation
Outdoor Temperature
Room
Temperature
Cooling
21°C ~ 43°C
21°C ~ 32°C
Dry
21°C ~ 43°C
21°C ~ 32°C
The unit does not operate.
Cooling is abnormally low.
• The power main switch is turned off.
• The circuit breaker is activated to
cut off the power supply.
• Stoppage of electric current.
• ON timer is set.
• The
fi
lters are blocked with dust.
• The temperature has been set
improperly.
• The windows or doors are opened.
• The air inlet or outlet of the outdoor
unit is blocked.
• The fan speed is too low.
• The operation mode is FAN or DRY.
TROUBLESHOOTING (CHECK POINT)
22
To start the sleep timer (OFF timer) operation
Press
SLEEP
: Select 1, 3, 5 or 9 hrs for OFF timer operation.
SLEEP TIMER OPERATION
18
REMOTE CONTROL A-B SELECTION
23
To separate using of remote control for each indoor unit in case of 2 air
conditioners are installed nearly.
Remote Control B Setup.
1. Press RESET button on the indoor unit to turn the air conditioner ON.
2. Point the remote control at the indoor unit.
3. Push and hold
CHK
●
button on the Remote Control by the tip of the pencil.
“00” will be shown on the display.
4.
Press
MODE
during pushing
CHK
●
. “B” will show on the display and “00” will
disappear and the air conditioner will turn OFF. The Remote Control B is
memorized.
Note:
1. Repeat above step to reset Remote
Control to be A.
2. Remote Control A has not “A” display.
3. Default setting of Remote Control from
factory is A.
SELF CLEANING OPERATION (COOL AND
DRY OPERATION ONLY)
20
To protect bad smell caused by the humidity in the indoor unit.
1.
If
the button is pressed once during “Cool” or “Dry” mode, the fan will continue
to run for other 20 minutes, then it will turn off automatically. This will reduce
the moisture in the indoor unit.
2. To stop the unit immediately, press the 3 times within 30 seconds.
Note:
• SELF CLEANING operation is default setting from factory.
• To cancel this function, please contact the supplying retail dealership.
Cleaning the plasma air puri
fi
er unit (About 1000 hours performed)
(SKDX Only)
1. Turn off air conditioner using remote control and power supply.
2. Take out the air inlet grille (See detail in installation manual).
3. Take out the plasma air puri
fi
er by grasp the handle, and the pull it out.
4. Soak in hot water at 40
o
C to 50
o
C for about 10 to 15 minutes and rub up,
down, left, right and rub surface gently with a sponge.
5. Allow to dry thoroughly in the shade.
6. Attach the plasma air puri
fi
er by grasp the handle and
insert into the right and left guide rails.
7. Press both ends of the plasma air puri
fi
er until the
protrusions on both sides of the plasma air puri
fi
er
are completely inserted.
8. Attach the air
fi
lter, and then close the air inlet grille.
Firstly, turn off the circuit breaker.
Filter Reset (Some models only)
FILTER lamp lights on; the
fi
lter must be cleaned.
To turn off the lamp, push the RESET button on the indoor unit or the FILTER
button on the remote control.
Indoor Unit and Remote Control
• Clean the indoor unit and the remote control with a wet cloth when needed.
• No benzine, thinner, polishing powder or chemically-treated duster.
Cleaning the air ionizer (Once every six months) (SKDX Only)
1. Turn off air conditioner using remote control and power supply.
2. Fully open the vertical air
fl
ow louvers by hand.
3. Use a toothbrush to rub the ends of metal pin
three or four times.
Note:
Do not use cotton swabs or other objects
with
fl
uff.
Even before 6 months since last cleaning,
clean the air ionizer if it is dirty.
MAINTENANCE
19
1110650101.indb 4
1110650101.indb 4
3/11/08 4:46:25 PM
3/11/08 4:46:25 PM
