manualshive.com logo in svg

Toshiba RAS-18PAVP-E, Installation Manual

Share
Download
Toshiba RAS-18PAVP-E Installation Manual Download Page 10

8

EN

Mounting the installation plate

When the installation plate is directly mounted on the wall

1.

Securely fit the installation plate onto the wall by screws with the upper and lower catches.

2.

To mount the installation plate on a concrete wall use anchor bolts. Drill the anchor bolt holes as illustrated in the above figure.

3.

Place the level at the top end of the installation plate, and check that the plate is horizontal.

• In case of block, brick, concrete or similar type walls, drill 5 mm dia. holes in the wall.
• Insert clip anchors for the 

e

 mounting screws.

NOTE

• Install the installation plate using between 4 to 6 mounting screws, making sure all four corners are secure.

1.

The supply voltage must be the same as the rated voltage of the air conditioner.

2.

Prepare a power source for the exclusive use of the air conditioner.

NOTE

• Wire type: H07RN-F or 60245IEC66 (1.0 mm

2

)

CAUTION

When installing the installation plate with mounting screws, do not use anchor bolt holes. Otherwise the unit may fall down and
result in personal injury and property damage.

CAUTION

Failure to securely install the unit may result in personal injury and/or property damage if the unit falls.

Electrical Work

100 mm

100 mm

Anchor bolt holes

Indoor unit

Pipe hole

Pipe hole

e

 Mounting screw

a

 Installation plate

Positions recommended for 
securing the screws (4 places)

Level (magnetic-backed) 
holder

Clip anchor 
(local parts)

e

 Mounting screw 

Dia. 4 x 25L

Anchor bolt

Projection 15 mm or less

5 mm dia. hole

Summary of Contents for RAS-18PAVP-E



























Reviews:

No comments

Brands by name

Popular brands

Load more brands