manualshive.com logo in svg

Toshiba RAS-10JAVP-E, Service Manual

Share
Download
Toshiba RAS-10JAVP-E Service Manual Download Page 40

– 40 –

8-6-2. Name and Functions of Indications on Remote Controller

[Display]

All indications, except for the clock time indicator, are displayed by pushing the   button.

6

TIMER and clock time display
The time setting for timer operation or the clock
time is indicated.
The current time is always indicated except during
TIMER operation.

7

Hi-POWER display
Indicates when the Hi-POWER operation starts.
Push the Hi POWER button to start and push it
again to stop the operation.

8

P

 (MEMORY) display

Flashes for 3 seconds when the MEMO button is
pushed during operation.
The 

P

 mark is shown when holding down the

button for more than 3 seconds while the mark is
flashing.
Push another button to turn off the mark.

9

ECO indicator
Indicates when the ECO is in activated.
Push the ECO button to start and push it again to
stop operation.

10

A, B change indicator remote controller
Push the CHECK point and MODE button at the
same time to change the remote controller setting
fron “A” to “B”. (Priority is given to the “A” setting.)
The E-Parts of the indoor unit are also changed to
the “B” setting.)

1

Transmission mark
This transmission mark   indicates when the
remote controller transmits signals to the indoor
unit.

2

Mode display
Indicates the current operation mode.
(AUTO : Automatic control, A : Auto changeover
control, 

 : Cool, 

 : Dry, 

 : Heat)

3

Temperature display
Indicates the temperature setting (17°C to 30°C).
When you set the operating mode to 

 : Fan only,

no temperature setting is indicated.

4

Air purifying indicator
Shows that the electrical air purifying operation is
in progress.

5

FAN speed display

Indicates the selected fan speed.  AUTO or five

fan speed levels (LOW   , LOW

+

 

 ,

MED 

 , MED

+

 

 , HIGH 

 ) can be

shown.
Indicates AUTO when the operating mode is
either AUTO or 

 : Dry.

• In the illustraBtion, all indications are indicated for explanation.

During operation, only the relevant indications will be indicated on the remote controller.

AUTO

3

9

5

7

6

1

2 8

4

10

A

OFF

PM

:

AUT

UTO

AUTOA

AM
PM

CHK

HiPOWER

ON
OFF

˚

C

:

AM
PM

:

P

B

AUTO

Summary of Contents for RAS-10JAVP-E
























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands