Toshiba MMY-MAP0806HT8JP-E, Owner'S Manual, Page: 16 / 25

03
01
02 04
Swing code
◆
To stop swinging
1
Push the button at the desired position
while the louver is swinging.
• Push the button repeatedly to change
the louver position again.
* However, even if the button is pushed
while the louver is swinging, one of the
indications below may sometimes be displayed
and may not set the louver to the highest
position.
▼ Indications when swinging is stopped
FAN/HEAT COOL/DRY
In this case, push the button again after 2
seconds.
• In COOL/DRY operation, the louver does not
stop as it directs downward. If stopping the
louver as it directs downward during swing
operation, it stops after moving to the third
position from the highest position.
▼ Indications when swinging is stopped
FAN/HEAT
operation COOL/DRY
operation
◆
Unit select
• When two or more indoor units are controlled
with one remote controller, the louver direction
can be set for each indoor unit by selecting them
individually.
• To set louver direction individually, push the
button (left side of the button) to display
an indoor unit number in the control group. Then
set the louver direction of the displayed indoor
unit.
• When no indoor unit number is displayed,
all indoor units in the control group can be
controlled simultaneously.
• Each time you push the (left side of the
button), the indication changes as follows:
◆
Setting the swing pattern
1
Push and hold the FIX for at least 4
seconds while the operation is stopped.
blinks.
2
Push the button (left side of the button)
to select a unit.
The unit number changes each time you push the
button.
Unit No.
1-1
Unit No.
1-2
Unit No.
1-3
No
display
Unit No.
1-4
The fan of the selected unit runs, and the louver
swings.
3
Push the buttons to select a swing type.
3
Push the button to con fi rm the direction
of the selected louver.
Each time you push the button, the indication
changes as follows:
(1) (2) (3) (4)
(7) (6) (5)
* When cooling or drying, (4) and (5) are not
displayed.
4
Push the button.
5
Push the button to fi nish the setting.
▼ Standard swing
All four louvers swing simultaneously at the same
angle.
▼ Dual swing (Recommended for heating)
• Adjoining louvers alternately point horizontally and
downward to heat the room evenly.
• Air blown downward reaches the fl oor, and air blown
horizontally is spread to circulate heat.
■
4-way cassette type only
◆
To set the louvers individually
1
Push the button (left side of the button)
during running to select a unit.
The unit number changes each time you push the
button.
Unit No.
1-1
Unit No.
1-2
Unit No.
1-3
No
display
Unit No.
1-4
• When no unit number is displayed, all units are
selected.
2
Push the button (right side of the
button) to select a louver.
Each time you push the button, the indicator
on the left of the remote controller changes as
follows:
No
display
* When no louver number is displayed, all 4
louvers are selected.
No
display
Unit No.
1-1
Unit No.
1-2
Unit No.
1-4
Unit No.
1-3
Louver No.
Electrical control box
Refrigerant
pipe
Drain pipe
Swing code Movement pattern
0001
Standard swing
(factory default)
0002 Dual swing
0003 Cyclic swing
REQUIREMENT
Do not set “0000”.
(The louver may be damaged.)
Horizontal
Swing
Horizontal
Horizontal
Horizontal
Downward
Downward
Downward
Downward
– 15 –
29-EN 30-EN