background image

– 3 –

SMMS-i

Owner’s Manual

SMMS-i

Owner’s Manual

• Consult the shop where you purchased the air conditioner if air conditioning (cooling and heating) is not performed 

properly as a refrigerant leakage may be the cause. Confirm the repair details with a qualified service person(*1) 
when the repair includes additional charging of the refrigerant. 

• Be sure to stop running the air conditioner and turn off the breaker before cleaning.

Otherwise, injury may result as the fan is rotating at high speed inside the unit.

Repairs

• When you have noticed that some kind of trouble (such as when an error display has appeared, there is a smell of burning, 

abnormal sounds are heard, the air conditioner fails to cool or heat or water is leaking) has occurred in the air conditioner, 

do not touch the air conditioner yourself but set the circuit breaker to the OFF position, and contact a qualified service 

person. Take steps to ensure that the power will not be turned on (by marking “out of service” near the circuit breaker, for 
instance) until qualified service person arrives. Continuing to use the air conditioner in the trouble status may cause 

mechanical problems to escalate or result in electric shocks, etc.

• If you have discovered that the fan grille is damaged, do not approach the outdoor unit but set the circuit breaker to the OFF 

position, and contact a qualified service person to have the repairs done. Do not set the circuit breaker to the ON position 

until the repairs are completed.

• If you have discovered that there is a danger of the indoor unit’s falling, do not approach the indoor unit but set the circuit 

breaker to the OFF position, and contact a qualified installer or a qualified service person to refit the unit. Do not set the 

circuit breaker to the ON position until the unit has been refitted.

• If you have discovered that there is a danger of the outdoor unit’s toppling over, do not approach the outdoor unit but set 

the circuit breaker to the OFF position, and contact a qualified installer or a qualified service person to have the 

improvements or refitting done. Do not set the circuit breaker to the ON position until the improvements or refitting is 

completed.

• Do not customize the unit. Doing so may result in fire, electric shock, etc.

Relocation

• When the air conditioner is to be relocated, do not relocate it yourself but contact a qualified installer or a qualified service 

person. Failure to relocate the air conditioner properly may result in electric shocks and/or a fire.

CAUTION

TO DISCONNECT THE APPLIANCE FROM THE MAINS SUPPLY

• This appliance must be connected to the mains by means of a switch with a contact separation of at least 

3 mm

.

THE INSTALLATION FUSE (ALL TYPES CAN BE USED) MUST BE USED FOR THE POWER SUPPLY LINE 
OF THIS AIR CONDITIONER.

CAUTIONS ABOUT INSTALLATION (Be sure to confirm the following cautions.)

• Certainly lay the drain hose for perfect draining. Bad drainage may cause flooding in the house and getting 

furniture wet.

• Make sure to connect the air conditioner to an exclusive power supply of the rated voltage, otherwise the unit 

may break down or cause a fire.

• Confirm that the outdoor unit are fixed on the base. Otherwise, falling down of the units or other accidents may 

occur.

CAUTIONS ABOUT OPERATION

• Do not use this air conditioner for special purpose such as preserving food, precision instruments, art objects, 

breeding animals, car, vessel, etc.

• Do not touch any switches with wet finger, otherwise you may get an electric shock.
• If the air conditioner will not be used for a considerably long time, turn off the main switch or the circuit breaker, 

for safety.

• To make the air conditioner operate in its original performance, operate it within the range of the operating 

temperature specified in the instructions. Otherwise it may cause a malfunction, or water leak from the unit.

• Prevent any liquid from falling into the remote controller. Do not spill juice, water or any kind of liquid.
• Do not wash the air conditioner. Doing so may result in electric shock.
• Check whether the installation base and other equipment have become deteriorated after being used for a long 

time. Leaving them such condition may result in the unit’s falling down and causing injury. 

• Do not leave flammable sprays or other flammable materials near the air conditioner, and do not spray flammable 

aerosol directly to the air conditioner. They may catch fire.

• Be sure to stop running the air conditioner and turn off the breaker before cleaning.

Otherwise, injury may result as the fan is rotating at high speed inside the unit.

• Ask for cleaning of the air conditioner to be performed by the dealer.

Cleaning the air conditioner in an improper manner may cause damage to plastic parts, insulation failure of 
electric parts, etc. and result in a malfunction. In the worst case, it may result in water leakage, electric shock, 
smoke emission and fire.

• Do not put a water container such as a vase on the unit.

Water intrusion into the unit may occur and it may cause deterioration of electric insulation and result in electric 
shock.

(*1) Refer to the “Definition of Qualified Installer or Qualified Service Person.”

5-EN

6-EN

+00EH99936401.book  Page 3  Thursday, August 26, 2010  6:52 PM

Summary of Contents for MMY-AP0804T8Z























Reviews: