Toshiba MMD-AP0076BHPUL Service Manual Download Page 87

Page: 87 / 102

11. DETACHMENTS

No.

Part name

Procedure

Remarks

WARNING

Be sure to stop operation of the air conditioner before

work and then turn off switch of the breaker.

CAUTION

Be sure to put on gloves during working time;

otherwise an injury will be caused by a part, etc.

NOTE

In a section, Detachments, the models are expressed as follows for convenience.

AP007 : MMD-AP0076BHPUL to MMD-AP0126BHPUL

AP015 : MMD-AP0156BHPUL to MMD-AP0186BHPUL

AP02

: MMD-AP02

BHPUL to MMD-AP0546BHPUL

Rear

air intake

Air filter

Arrow mark

Air filter

Bottom

air intake

1. Detachment

1) Slide the filter toward the opposite side of

the arrow mark and then pull out the filter.

(In the case that two filters are provided,

pull out the first filter, then the second filter

will be pulled out connected with the first

filter.)

2. Attachment

1) Insert the filter in the filter rail toward the

arrow mark, slide it until the filter stops and

then fix it.

(In the case that two filters are provided,

insert the second filter in the same

direction after inserting the first filter.)

Air filter

- 87 -

Summary of Contents for MMD-AP0076BHPUL







































































































Search results

Summary of Contents for MMD-AP0076BHPUL

Reviews:

Related manuals for MMD-AP0076BHPUL

Brands by name

Popular brands

Toshiba MMD-AP0076BHPUL, Service Manual

Search results

Summary of Contents for MMD-AP0076BHPUL

Reviews:

Related manuals for MMD-AP0076BHPUL

Brands by name

Popular brands