Toshiba MAR-C104M8-1-PE Service Manual Download Page 48

Page: 48 / 73

Fault

Code

Symptom

Status of Air

Conditioner

Notes

Diagnostic Functions

INVERTER
COMPRESSOR FAULT

Operation

stops

INVERTER
MALFUNCTION

Operation

stops

1. Fault in the current detection circuit of the Inverter

control board.

2. Check the power circuit, wiring, control boards and

compressor.

OUTDOOR
HEAT EXCHANGER
SENSOR (TE)

Operation

stops

HIGH PRESSURE
FAULT

Operation

stops

1. High pressure switch or Inner over-load relay

malfunction.

2. Operation of the High pressure switch or Inner over-

load relay, or detected by the Pressure sensor.

3. Possible causes – gas leak, refrigerant under charge

or over-load operating conditions.

4. Phase rotation detected at D.O.L compressor start

up. "Check" flashes on the Remote controller.

1. Sensor open / short circuit.

2-Pipe Outdoor unit
ONLY.

1. Inverter compressor fault (overload).

2. Check the power supply, wiring and compressor.

REMOTE
CONTROLLER
COMMUNICATION

Indoor unit

stops

1. Wiring fault between the Indoor unit and the Remote

controller.

Summary of Contents for MAR-C104M8-1-PE










































































Search results

Summary of Contents for MAR-C104M8-1-PE

Reviews:

Brands by name

Popular brands

Toshiba MAR-C104M8-1-PE, Service Manual

Search results

Summary of Contents for MAR-C104M8-1-PE

Reviews:

Brands by name

Popular brands