background image

File No. 960-140

3-29

3.12 Real Timer Test

To execute the Real Timer Test, select 

9

 from the DIAGNOSTIC TEST MENU, press 

Enter

and follow the directions on the screen. The real timer test contains three subtests that test the
computer’s real timer functions. Move the highlight bar to the subtest you want to execute
and press 

Enter

.

Subtest 01

Real time

A new date and time can be input during this subtest. To execute the real time
subtest follow these steps:

1.

 

Select subtest 01 and the following message will appear:

Current  date : XX-XX-XXXX
Current  time : XX:XX:XX

Enter new date:

PRESS [ENTER] KEY TO EXIT TEST

2.

 

If the current date is not correct, input the correct date at the “Enter new
date” prompt and press 

Enter

. The following prompt will appear:

Enter new  time :

3.

 

If the current time is not correct, input the correct time in 24-hour format.

Pressing 

Enter 

toggles between the time and the date. To exit, press 

Ctrl +

Break.

Subtest 02

Backup memory

This subtest performs the following backup memory check:

Writes 1-bit of “on” data to address 01h through 80h
Writes 1-bit of “off” data to address 0Eh through 80h
Writes the data pattern AAh and 55h to the RTC 114-byte memory
(address 0Eh to 7Fh)

The subtest then reads and compares this data with the original data.

To exit, press 

Ctrl + Break

.

Summary of Contents for Libretto 100CT













































































































































































































































Reviews: