GX9 ASD Installation and Operation Manual
121
BIN Reference Point 2
Program
Frequency
Speed Reference Setpoints
This parameter is used to set the speed of the
BIN
terminals when the
BIN
terminals are used as the control input.
This parameter sets the
BIN
signal that is associated with
BIN Input Point 2
Frequency
.
This value is entered as 0% to +100% of the
BIN
signal range.
See
BIN Reference Point 1
(
)
for further information on this setting.
Direct Access Number — F230
Parameter Type —
Numerical
Factory Default —
100.00
Changeable During Run —
Yes
Minimum — 0.00
Maximum — 100.00
Units — %
BIN Input Point 2 Frequency
Program
Frequency
Speed Reference Setpoints
This parameter is used to set the speed of the
BIN
terminals when the
BIN
terminal are used as the control input.
This parameter sets
BIN Input Point 2 Frequency
and is the frequency that is
associated with the setting of
BIN Reference Point 2
.
See
BIN Reference Point 1
(
)
f
or further information on this setting.
Direct Access Number — F231
Parameter Type —
Numerical
Factory Default —
80.0
Changeable During Run —
Yes
Minimum — -
Max. Freq.
(
Maximum —
Max. Freq.
Units — Hz
BIN Input Point 1 Torque
Program
Torque
Setpoints
This parameter is used to set the direction, gain, and bias of the
BIN
binary input
terminals when these
terminals are used as the control input while operating in
the
Torque Control
mode.
This is accomplished by establishing an associated
V/f
output pattern for a given
BIN
binary input and motor load.
See
for further information on this setting.
This parameter sets
BIN Input Point 1 Torque
and is entered as
-250 to +250% of the rated torque.
Direct Access Number — F232
Parameter Type —
Numerical
Factory Default —
0.00
Changeable During Run —
Yes
Minimum — -250.00
Maximum — +250.00
Units — %
BIN Input Point 2 Torque
Program
Torque
Setpoints
This parameter is used to set the direction, gain, and bias of the
BIN
binary input
terminals when these
terminals are used as the control input while operating in
the
Torque Control
mode.
This is accomplished by establishing an associated
V/f
output pattern for a given
BIN
binary input and motor load.
See
for further information on this setting.
This parameter sets
BIN Input Point 2 Torque
and is entered as
-250 to +250% of the rated torque.
Direct Access Number — F233
Parameter Type —
Numerical
Factory Default —
100.00
Changeable During Run —
Yes
Minimum — -250.00
Maximum — +250.00
Units — %
Summary of Contents for GX9
