Toshiba e-STUDIO557 Copying Manual Download Page 69

Page: 69 / 180

3.BASIC COPY MODES

Selecting Finishing Mode 67

3 BASIC COPY MODES

Staple sort mode

When you make more than one set of copies, the copied paper can be automatically stapled set by set. This
mode is called the staple sort mode. You can choose from 3 different stapling positions.

Example: When [FRONT STAPLE] is selected

Special paper such as OHP film or sticker labels is not applicable.

Copies in different sizes cannot be stapled. (If the lengths of the copies are the same, they can be
stapled.)

Place paper in the drawer(s).

When using bypass copying, be sure to set the paper size.

Place the original(s).

Press [FINISHING] on the touch panel.

Select the desired stapling position from [FRONT STAPLE], [DOUBLE STAPLE] or
[REAR STAPLE], and then press [OK].

Select other copy modes as required, and then press the [START] button on the control
panel.

When the number of sheets exceeds the maximum number of sheets available for stapling, this
equipment automatically enters into the sort mode.

Summary of Contents for e-STUDIO557




















































































































































































Search results

Summary of Contents for e-STUDIO557

Reviews:

Related manuals for e-STUDIO557

Brands by name

Popular brands

Toshiba e-STUDIO557, Copying Manual

Search results

Summary of Contents for e-STUDIO557

Reviews:

Related manuals for e-STUDIO557

Brands by name

Popular brands