Toshiba e-STUDIO160 Service Handbook Download

Page: 185 / 239

December 2002 TOSHIBA TEC

4 - 63

e-STUDIO160/200/250 TROUBLESHOOTING

(5) White banding (in feeding direction)

Step

Cause/Defect area

Paper feed path

Laser scanner unit

Transfer charger unit

Process unit

(Magnetic roller)

Process unit (Doctor blade)

Process unit (Drum)

Measures

Remove the foreign matter.

Remove the foreign matter or dust with blower.

(Do not use a cloth.)

Remove the foreign matter.

Clean the wire, or remove the foreign matter.

Replace the transfer charger unit.

Clean the area between the magnetic roller

and doctor blade with the doctor blade clean-

ing jig.

Adjust the doctor-sleeve gap. If the problem

persists, replace the doctor blade.

If the problem persists, replace process unit

or drum.

Note:

Never touch drum surface.

Replace the process unit, laser scanner unit,

or transfer charger unit.

Check items

Does toner image touch foreign

matter after separation, before

entering fuser unit.

Foreign matter or dust on lens?

Is there a foreign matter blocking

off laser beam in the path?

Does a foreign material or stain

adhere to the transfer wire?

Transfer charger wire slacked?

Transfer charger case deformed?

White banding on the magnetic

roller? (Is there a foreign matter

between the magnetic roller and

doctor blade?)

Is the doctor-sleeve gap within the

specified value?

Any abnormalities on drum sur-

face?

If problem persists after measures

are applied, or there is no prob-

lem found in above check, follow

procedure described in the right

column.

Feeding direction

Summary of Contents for e-STUDIO160















































































































































































































































Search results

Summary of Contents for e-STUDIO160

Reviews:

Related manuals for e-STUDIO160

Brands by name

Popular brands

Toshiba e-STUDIO160, Service Handbook

Search results

Summary of Contents for e-STUDIO160

Reviews:

Related manuals for e-STUDIO160

Brands by name

Popular brands