Toshiba E-Studio 5540c Troubleshooting Manual Download Page 59

Page: 59 / 118

1 TROUBLESHOOTING FOR THE HARDWARE

Refilling With Staples 57

Refilling With Staples

Refill with staples according to the following procedures when the staples in the stapler of the finisher and Saddle Stitch
unit run out.

P.57 “Refilling the Finisher staples”

P.58 “Refilling the Saddle Stitch unit staples”

Refilling the Finisher staples

Open the front cover of the finisher.

Remove the staple cartridge.

Take the empty staple case out of the staple
cartridge.

Pull up the empty staple case while pushing both sides as shown in
the figure.

Fit a new staple case into the staple cartridge.

Push the staple case hook into the staple cartridge socket until you
hear a click.

Summary of Contents for E-Studio 5540c























































































































Search results

Summary of Contents for E-Studio 5540c

Reviews:

Related manuals for E-Studio 5540c

Brands by name

Popular brands

Toshiba E-Studio 5540c, Troubleshooting Manual

Search results

Summary of Contents for E-Studio 5540c

Reviews:

Related manuals for E-Studio 5540c

Brands by name

Popular brands