Toshiba D-R2SC Owner'S Manual Download

Page: 14 / 56

Connecting an antenna and TV

Connect your TV and the antenna to this recorder for recording and to view broadcast signals on the TV.

Connections

Disconnect the antenna cable from your TV, and connect it to the RF IN
(FROM ANT.) terminal on the recorder.

Using the supplied coaxial cable of this recorder, connect the RF OUT (TO
TV) terminal to the TV.

VHF/UHF antenna

Antenna cable (not supplied)

To RF IN (FROM ANT.)

To RF OUT (TO TV)

Coaxial cable (supplied)

To antenna input

e.g.

For connecting to a cable box or a satellite system, see

page 16 to 19.

Note
• This connection insures accessibility of broadcast signals to your TV only. Unlike a VCR, you can not assign channel 3 or 4

for playback of this recorder, because an antenna input only passes through in the recorder. You must connect this recorder
to a video input of your TV to enjoy playback picture from this recorder. (See the next page.)

Types of an antenna terminal may vary depending
on the TV.
Check the type on your TV, and connect properly
using either method as shown.

Antenna splitter (not supplied)

VHF/UHF

VHF / UHF

VIDEO

S-VIDEO

S-VID

RF OUT
(TO TV)

RF IN
(FROM ANT.)

CHANNEL

CHANGE

Summary of Contents for D-R2SC

























































Search results

Summary of Contents for D-R2SC

Reviews:

Related manuals for D-R2SC

Brands by name

Popular brands

Toshiba D-R2SC, Owner'S Manual

Search results

Summary of Contents for D-R2SC

Reviews:

Related manuals for D-R2SC

Brands by name

Popular brands