Toshiba BU302M Manual Download Page 24

Page: 24 / 35

D4253375C

http://www.toshiba-teli.co.jp/en/index.htm

6.6

GPIO Output signal specification

I/O Connector Pin No.

2 Pin : Line1

Output signal

TIMER0 ACTIVE, USER OUTPUT, EXPOSURE ACTIVE,

FRAME ACTIVE, FRAME TRANSFER, FRAME TRIGGER WAIT

Output level

5V CMOS

Maximum Current

+/-32mA

Polarity

High active / Low active (factory setting : Low active)

Timer0 Active

Delay

0 to 2000000

μs (factory setting : 0μs)

Duration

0 to 2000000

μs (factory setting : 0μs)

TimerTriggerSource

Line0Active, ExposureStart, FrameTrigger

6.7

Interface specification

Interface

USB 3.0 (Only SuperSpeed is supported)

Transmission speed

5Gbps (Maximum)

Protocol

USB3 Vision

6.8

LED states

Camera state

Lamp indication

No power

Off

Link detection in progress

Fast flash green (ON:20ms, OFF:60ms)

Connection Error

Flash alternate red / green

SuperSpeed connected, but no data being transferred Flash green (ON: 200ms, OFF: 800ms)

SuperSpeed connected, waiting for trigger

Flash orange (ON: 200ms, OFF: 800ms)

Data being transferred

Fast flash green (ON:60ms, OFF:20ms)

Error during data transfer

Solid Red (Time period: 500ms)

Stand-by

Super slow flash orange (ON:200ms, OFF: 2800ms)

Summary of Contents for BU302M


































Search results

Summary of Contents for BU302M

Reviews:

Related manuals for BU302M

Brands by name

Popular brands

Toshiba BU302M, Manual

Search results

Summary of Contents for BU302M

Reviews:

Related manuals for BU302M

Brands by name

Popular brands