Toshiba BMS-IFMB1280U-E Installation Manual Download Page 4

Page: 4 / 22

Modbus interface

Installation Manual

Introduction



Applications / Functions / Specifications

Applications

• The Modbus interface is used to connect air conditioners “with TU2C-LINK Uh Line (hereinafter, referred to as

Uh Line) installed” and TCB-IFCG1TLE to Modbus* system.

Functions

• The Modbus interface converts signals between Uh Line and Modbus Master.

Specifications

* Note) “Modbus” is a registered trade mark of Schneider Electric SA.



External view

Power supply

220 - 240 VAC, 50/60 Hz

Power consumption

3 W

Operating temperature / humidity

0 to 40 °C, 10 to 90 % RH (no condensation)

Storage temperature

-20 to +60 °C

Chassis material

Galvanized sheet metal 0.8 t (no coating)

Dimensions

66 (H) x 170 (W) x 200 (D) mm

Mass

1.1 kg

146.9

170

156

200

63.6

6-Ø5.5 mounting

holes

3-EN

Summary of Contents for BMS-IFMB1280U-E























Search results

Summary of Contents for BMS-IFMB1280U-E

Reviews:

Related manuals for BMS-IFMB1280U-E

Brands by name

Popular brands

Toshiba BMS-IFMB1280U-E, Installation Manual

Search results

Summary of Contents for BMS-IFMB1280U-E

Reviews:

Related manuals for BMS-IFMB1280U-E

Brands by name

Popular brands