manualshive.com logo in svg

Toshiba Bar Code Printer, Network Tool Operation Manual, Page: 65 / 69

Share
Download
Toshiba Bar Code Printer Network Tool Operation Manual Download Page 65

65 

Screens Displayed and Used by This Feature 

This section explains each screen.   

[Obtaining printer information] Screen   

This screen appears while the printer is obtaining printer 
information.  
 
 

[Printer Selection] Screen   

This screen appears when the downloader is started alone or 
when no printer information has been recorded.   
You will list a printer by clicking [Printer Search] or   
[Add Printer…]. 
   
 
 
 
 
 
 
 
 
When the printer is searched and added, the right figure 
appears.    If a printer you want to use is not on the list, please 
list the printer by clicking [Printer Search] or [Add Printer].   
When several printers are on the list, you can select a printer 
using the search function at the bottom of the screen.   
 
 
 
 
 
 
 
 

[Add Printer…] Screen 

This screen appears when you click [Add Printer] on the   
[Printer Selection] screen.   
Available connection: LAN, COM (serial port), LPT, or USB   
 

 

Items to be set for each connection 
LAN : 

IP 

address 

COM 

:  Transmission speed, data length, parity, 

stop bit   

LPT, USB  :  None 
(The right figure is for the case when LAN is selected.) 

Note:  If you are using the Supported Printers without using the 

printer driver, the printer driver installation screen appears 
when the Supported Printers are connected to a 
computer via USB.   
In such case, please install the printer driver following the 
instructions on the screen.   

 
 
 

Summary of Contents for Bar Code Printer






































































Reviews:

No comments