Toshiba B-EX 2 Series Quick Installation Manual Download Page 8

Page: 8 / 8

E-8

4. Turning the Printer ON/OFF

When the printer is connected to your host computer it is good practice to turn the printer ON
before turning on your host computer and turn OFF your host computer before turning off the
printer.

4.1 Turning ON the Printer

1. To turn ON the printer power, press the Power

Switch as shown in the diagram below. Note that
( | ) is the power ON side of the switch.

2. Check that the ON LINE message appears in the

LCD Message Display and that the ON LINE and
POWER LED lights are illuminated.

4.2 Turning OFF the Printer

1. Before turning off the printer Power Switch verify

that the ON LINE message appears in the LCD
Message Display and that the ON LINE LED light
is on and is not flashing.

2. To turn OFF the printer power, press the Power

Switch as shown in the diagram below. Note that
(O) is the power OFF side of the switch.

CAUTION!

Use the power switch to turn the printer On/Off. Plugging or unplugging the Power Cord to turn the
printer On/Off may cause fire, an

electric shock, or damage to the printer.

NOTE:

If a message other than ON LINE appears on the display or the ERROR LED lamp is illuminated, refer to

Owners manual

Error Messages

CAUTION!

1. Do not turn off the printer power while the media is being printed as this may cause a paper jam

or damage to the printer.

2. Do not turn off the printer power while the ON LINE lamp is blinking as this may cause damage

to your computer.

Power Switch

< For EU only >
TOSHIBA TEC Europe Retail Information Systems S.A
Rue de la Célidée 33 BE-1080 Brussels
www.toshibatec-eu.com

PRINTED IN INDONESIA
EO1-33097C

Summary of Contents for B-EX 2 Series









Search results

Summary of Contents for B-EX 2 Series

Reviews:

Brands by name

Popular brands

Toshiba B-EX 2 Series, Quick Installation Manual

Search results

Summary of Contents for B-EX 2 Series

Reviews:

Brands by name

Popular brands