background image

Form No. 3428-370 Rev C

30in TurfMaster

HDX Walk-Behind Lawn Mower

Model No. 22215—Serial No. 400000000 and Up

Operator's Manual

Introduction

This rotary-blade, walk-behind lawn mower is intended
to be used by professional, hired operators. It is
designed primarily for cutting grass on well-maintained
lawns on residential or commercial properties. Using
this product for purposes other than its intended use
could prove dangerous to you and bystanders.

Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. You are responsible for
operating the product properly and safely.

Visit www.Toro.com for more information, including
safety tips, training materials, accessory information,
help finding a dealer, or to register your product.

Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready.

Figure 1

identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.

Important:

With your mobile device, you can

scan the QR code on the serial number decal (if
equipped) to access warranty, parts, and other
product information

g226625

Figure 1

1.

Model and serial number location

Model No.

Serial No.

This manual identifies potential hazards and has
safety messages identified by the safety-alert symbol
(

Figure 2

), which signals a hazard that may cause

serious injury or death if you do not follow the
recommended precautions.

g000502

Figure 2

Safety-alert symbol

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical

information and

Note

emphasizes general information

worthy of special attention.

It is a violation of California Public Resource Code
Section 4442 or 4443 to use or operate the engine on
any forest-covered, brush-covered, or grass-covered
land unless the engine is equipped with a spark
arrester, as defined in Section 4442, maintained in
effective working order or the engine is constructed,
equipped, and maintained for the prevention of fire.

The enclosed engine owner's manual is supplied
for information regarding the US Environmental
Protection Agency (EPA) and the California Emission
Control Regulation of emission systems, maintenance,
and warranty. Replacements may be ordered through
the engine manufacturer.

Gross or Net Torque:

The gross or net torque

of this engine was laboratory rated by the engine
manufacturer in accordance with the Society of
Automotive Engineers (SAE) J1940 or J2723. As
configured to meet safety, emission, and operating
requirements, the actual engine torque on this class
of mower will be significantly lower. Please refer to
the engine manufacturer’s information included with
the machine.

WARNING

CALIFORNIA

Proposition 65 Warning

The engine exhaust from this product

contains chemicals known to the State of

California to cause cancer, birth defects,

or other reproductive harm.

Use of this product may cause exposure

to chemicals known to the State of

California to cause cancer, birth defects,

or other reproductive harm.

© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in Mexico

All Rights Reserved

*3428-370* C

 

Summary of Contents for TurfMaster HDX









































Reviews: