Toro TimeCutter ZD530 Operator'S Manual Download Page 48

Page: 48 / 52

Problem

Possible Cause

Corrective Action

1. Collection bag is full.

1. Empty the collection

bag.

Collection sensor alarm

sounding.

2. Debris is covering sensor. 2. Remove collection bag

and clean sensors with

soft cloth.

1. The blade(s) is not sharp. 1. Sharpen the blade(s).
2. A cutting blade(s) is/are

bent.

2. Install a new cutting

blade(s).

3. The mower is not level.

3. Level the mower

from side-to-side and

front-to-rear.

4. An anti-scalp wheel is

not set correctly.

4. Adjust the anti-scalp

wheel height.

5. The underside of the

mower is dirty.

5. Clean the underside of

the mower.

6. The tire pressure is

incorrect.

6. Adjust the tire pressure.

Uneven cutting height.

7. A blade spindle is bent.

7. Contact an Authorized

Service Dealer.

1. The drive belt is worn,

loose or broken.

1. Install a new drive belt.

2. The drive belt is off of the

pulley.

2. Install the drive belt

and check the adjusting

shafts and belt guides for

the correct position.

3. The mower belt is worn,

loose, or broken.

3. Install a new mower belt.

The blades do not rotate.

4. Collection bag is not

properly installed.

4. Check the bag and make

sure it is seated ush

with machine frame

and presence switch is

engaged.

Summary of Contents for TimeCutter ZD530





















































Search results

Summary of Contents for TimeCutter ZD530

Reviews:

Brands by name

Popular brands

Toro TimeCutter ZD530, Operator'S Manual

Search results

Summary of Contents for TimeCutter ZD530

Reviews:

Brands by name

Popular brands