manualshive.com logo in svg

Toro TimeCutter SS 4250, Operator'S Manual

Share
Download
Toro TimeCutter SS 4250 Operator'S Manual Download Page 39

G009682

1

2

2

3

3

4

4

Figure 54

1.

Blades side to side

3.

Outside cutting edges

2.

Sail area of blade

4.

Measure from the tip of the
blade to the flat surface
here

5.

Measure between the outside cutting edges and the
flat surface (

Figure 54

). If both measurements are not

within 3/16 inch (5 mm), an adjustment is required;
continue with this procedure.

6.

Move to the left side of the machine.

7.

Loosen the side locking nut.

8.

Raise or lower the left side of the mower deck by
rotating the rear nut. (

Figure 55

).

Note:

Rotate the rear nut clockwise to raise the mower

deck; rotate the rear nut counter-clockwise to lower
the mower deck.

Figure 55

1.

Hanger bracket

3.

Rear locking nut

2.

Side locking nut

9.

Check the side-to-side adjustments again. Repeat this
procedure until the measurements are correct.

10.

Continue leveling the deck by checking the front-to-rear
blade slope; refer to

Adjusting the Front-to-Rear Blade

Slope (page 39)

.

Adjusting the Front-to-Rear Blade
Slope

Check the front-to-rear blade level any time you install the
mower. If the front of the mower is more than 5/16 inch
(7.9 mm) lower than the rear of the mower, adjust the blade
level using the following instructions:

1.

Park the machine on a level surface and disengage the
blade-control switch.

2.

Move the motion-control levers outward to the park
position, stop the engine, remove the key, and wait for
all moving parts to stop before leaving the operating
position.

3.

Set the height-of-cut lever to middle position.

Note:

Check and adjust the side-to-side blade level if

you have not checked the setting; refer to Side-to-Side
Leveling.

4.

Carefully rotate the blades so they are facing front to
rear (

Figure 56

).

G009658

1

2

2

Figure 56

1.

Blades front to rear

2.

Measure from the tip of the blade to the flat surface here

5.

Measure from the tip of the front blade to the flat
surface and the tip of the rear blade to the flat surface
(

Figure 56

). If the front blade tip is not 1/16-5/16 inch

(1.6-7.9 mm) lower than the rear blade tip, adjust the
front locknut.

6.

To adjust the front-to-rear blade slope, rotate the
adjustment nut in the front of the mower (

Figure 57

).

39

 

Summary of Contents for TimeCutter SS 4250

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands