manualshive.com logo in svg

Toro TimeCutter SS 4250, Operator'S Manual

Share
Download
Toro TimeCutter SS 4250 Operator'S Manual Download Page 32

Fuel System
Maintenance

DANGER

In certain conditions, gasoline is extremely
flammable and highly explosive. A fire or explosion
from gasoline can burn you and others and can
damage property.

•

Perform any fuel related maintenance when the
engine is cold. Do this outdoors in an open area.
Wipe up any gasoline that spills.

•

Never smoke when draining gasoline, and stay
away from an open flame or where a spark may
ignite the gasoline fumes.

Replacing the In-Line Fuel
Filter

Service Interval:

Every 200 hours—Replace the in-line fuel

filter

Never install a dirty filter if it is removed from the fuel line.

1.

Park the machine on a level surface and disengage the
blade-control switch.

2.

Move the motion-control levers outward to the park
position, stop the engine, remove the key, and wait for
all moving parts to stop before leaving the operating
position.

g027939

B

A

C

D

g027753

Figure 40

32

 

Summary of Contents for TimeCutter SS 4250

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands