manualshive.com logo in svg

Toro Security Cage Kit, Installation Instructions Manual, Page: 7 / 8

Share
Download
Toro Security Cage Kit Installation Instructions Manual Download Page 7

6

Installing the Windshield

Parts needed for this procedure:

1

Dual-tab mount

2

Side-tab mount

1

Top-tab mount

6

Rivet

1

Lower-windshield assembly

1

Upper-windshield assembly

13

Bolt (5/16 x 1-1/2 inches)

13

Backup washer

13

Rubber bushing (0.31 inch long)

13

Rubber bushing (0.56 inch long)

13

Nut (5/16 inch)

Procedure

Refer to

Figure 7

as you perform the following steps.

Note:

Ensure that the upper windshield is installed so

that the seam is positioned on the bottom of the frame.

1.

Install the dual-tab mount between the upper
and lower windshield frame on the ROPS.

2.

Use 2 rivets to secure the 2 side-tab mounts
into the holes provided in the 2-post ROPS
extension pillar cover.

3.

Use a rivet to secure the top-tab mount into the
hole provided in the 2-post ROPS extension
front panel.

4.

Install the lower and upper windshield
assemblies with 13 bolts (5/16 x 1-1/2 inches),
13 backup washers, 13 rubber bushings (0.31
inch long), 13 rubber bushings (0.56 inch long),
and 13 nuts (5/16 inch).

g211834

Figure 7

1.

Dual-tab mount

5.

Lower windshield assembly

9.

Rubber bushing (0.31 inch long)

2.

Side-tab mount

6.

Upper windshield assembly

10.

Rubber bushing (0.56 inch long)

3.

Top-tab mount

7.

Bolt (5/16 x 1-1/2 inches)

11.

Nut (5/16 inch)

4.

Rivet

8.

Backup washer

12.

Seam

7

 

Summary of Contents for Security Cage Kit









Reviews:

No comments