background image

Form No. 3406-569 Rev B

48in, 52in, or 60in Recycler

®

Kit

TITAN

®

HD 1500, 2000, or 2500 Series Riding Mower

Model No. 126-8701

Model No. 126-8702

Model No. 126-8703

Model No. 133-2166

Model No. 133-2167

Model No. 133-2168

Installation Instructions

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals known to the State of California to

cause cancer, birth defects, or reproductive harm.

Safety

Using the Side-Discharge
Mode or Mulching Grass

WARNING

Without the grass deflector, discharge cover, or
complete grass catcher assembly mounted in
place, you and others are exposed to blade contact
and thrown debris. Contact with rotating mower
blade(s) and thrown debris will cause injury or
death.

Never remove the grass deflector from the mower
because the grass deflector routes material down
toward the turf. If the grass deflector is ever
damaged, replace it immediately.

Never put your hands or feet under the mower.

Never try to clear the discharge area or mower
blades unless you disengage the power-take-off
(PTO) lever and turn the ignition key to off.
Also remove the key and pull the wire off the
spark plug(s).

© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3406-569* B

 

Summary of Contents for Recycler 126-2166













Reviews: