Toro Greensmaster TriFlex 3400 Series Operator'S Manual Download Page 21 | Manualshive

Page: 21 / 48

background image

g014620

Figure 20

1.

Backlap lever—mow
position

2.

Backlap lever—backlap
position

Reel Speed Control

The reel speed control is located under the plastic
cover to the left of the seat. Use the reel speed control
(

) to adjust the rpm of the reels.

g014623

Figure 21

1.

Reel speed control

Seat Adjusting Lever

The seat adjusting lever is located on the front, right
corner of the seat (

), allowing you to adjust

the seat fore and aft.

Note:

If you need additional adjustment on the seat,

you can remove the four bolts securing the seat to the
base and move the seat to the second set of mounting
holes provided.

g014628

Figure 22

1.

Seat adjusting handle

Fuel Shutoff Valve

Close the fuel shutoff valve (

), behind

the seat and under the fuel tank, when storing or
transporting the machine on a truck or trailer.

g014626

Figure 23

1.

Fuel shutoff (under the fuel tank)

21

«
...
19
20
21
22
23
...
»

Summary of Contents for Greensmaster TriFlex 3400 Series

















































Reviews:

No comments

Related manuals for Greensmaster TriFlex 3400 Series

Brand: GE Pages: 2

Druck DPI 620 Genii

Brand: GE Pages: 154

Arize Element Top Light

Brand: GE Pages: 2

Druck DPI 620 Genii

Brand: Baker Hughes Pages: 166

Druck DPI 620 Genii

Brand: Baker Hughes Pages: 340

Brand: Datalogic Pages: 48

Brand: PageFlip Pages: 32

Brand: Quivogne Pages: 13

ActiveFinder One

Brand: LaserLiner Pages: 92

Brand: MagCore Pages: 80

Brand: MagCore Pages: 80

Brand: Omlet Pages: 2

Brand: Omicron Pages: 382

Brand: Omicron Pages: 188

Brand: Walinga Pages: 20

Brand: ?HC Pages: 2

ABS-Lock III-BE

Brand: ABS Pages: 8

Brand: Garmin Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands