background image

8

2. Position side plates outside housing side flanges, with

cutting edges parallel to side of housing, and secure
with 6 carriage bolts (3/8 x 1 in.) (heads to the inside),
6 washers (3/8 in.) and 6 locknuts (3/8 in.) (Fig. 3).

1

5

4

6

3

1281

4

3

2

2

5

Figure 3

1.

Top plate

2.

Carriage bolt, 3/8 x 1 in.

3.

Washer, 3/8 in.

4.

Locknut, 3/8 in.

5.

Side plate

6.

Cutting edge

Installing the Discharge Chute
and Rotator Assembly

1. Assemble upper discharge chute outside and on top of

lower discharge chute with 2 bolts (5/16 x 5/8 in.)
(heads on the inside), 2 washers (5/16 in.) and 2
locknuts (5/16 in.) (Fig. 4).

1290

1

3

2

5

4

Figure 4

1.

Upper discharge chute

2.

Lower discharge chute

3.

Carriage bolt,
5/16 x 5/8 in.

4.

Washer, 5/16 in.

5.

Locknut, 5/16 in.

2. Install discharge chute and deflector shield onto

housing with

 

3 carriage bolts (5/16 x 3/4 in.) (heads to

the inside), 3 washers (5/16 in.) and 3 locknuts (5/16
in.) (Fig. 5).

2

3

4

2241

5

1

Figure 5

1.

Discharge chute

2.

Deflector shield

3.

Carriage bolt, 5/16 x
3/4 in.

4.

Washer, 5/16 in.

5.

Locknut, 5/16 in.

3. Install discharge chute rotator assembly into slot in

housing with 3 carriage bolts (5/16 x 1) (head to the
top), 3 pyramidal washers (5/16 in.) and 3 locknuts
(5/16 in.) (Fig. 6).

4. Adjust rotator assembly so that worm gear is at right

angle with chute, the teeth mesh fully and the chute
turns freely. tighten locknut securely.

1

2

3

1280

4

5

Figure 6

1.

Rotator assembly

2.

Carriage bolt, 5/16 x 1 in.

3.

Pyramidal washer, 5/16 in.

4.

Locknut, 5/16 in.

5.

Worm gear

Summary of Contents for 79362





















Reviews: