Toro 74959 Operator'S Manual Download Page 13 | Manualshive

Page: 13 / 64

background image

Ignition Switch

This switch is used to start the mower engine and has 3
positions:

Start, Run,

and

Off

.

Motion Control Levers

The motion control levers are used to drive the machine
forward, reverse, and turn either direction.

Neutral Lock Position

The neutral lock position is used with the safety interlock
system to engage and to determine neutral position.

Fuel Shut-off Valve

Close the fuel shut-off valve (under the seat) when
transporting or storing the mower.

Attachments/Accessories

A selection of Toro approved attachments and accessories is
available for use with the machine to enhance and expand
its capabilities. Contact your Authorized Service Dealer or
Distributor or go to www.Toro.com for a list of all approved
attachments and accessories.

Specifications

Note:

Specifications and design are subject to change

without notice.

Width:

72 inch Deck

Without Deck

150.1 cm (59.1 inches)

Deflector Up

187 cm (73.6 inches)

Deflector Down

222.4 cm (87.6 inches)

Length:

72 inch Deck

Roll Bar - Up

218.7 cm (86.1 inches)

Roll Bar - Down

223 cm (87.8 inches)

Height:

Roll Bar - Up

Roll Bar - Down

179.1 cm (70.5 inches)

118.9 cm (46.8 inches)

Weight:

Model

Weight

74959

588 kg (1296 lbs)

13

«
...
11
12
13
14
15
...
»

Summary of Contents for 74959

































































Reviews:

No comments

Related manuals for 74959

Brand: Murray Pages: 56

Brand: Gardenline Pages: 28

Brand: Snapper Pages: 40

Brand: Dixon Pages: 44

EXPERIENCE Estate 798e

Brand: Stiga Pages: 1052

Wheel Horse XL 380H

Brand: Toro Pages: 40

Brand: MTD Pages: 16

Brand: Fieldmaster Pages: 25

SILENT 40 EL 8211-3427-04

Brand: Stiga Pages: 8

Brand: Cub Cadet Pages: 44

Brand: Snapper Pages: 15

Brand: Snapper Pages: 24

Brand: Snapper Pages: 12

Brand: Snapper Pages: 52

Brand: Snapper Pages: 54

LT115D331B Series

Brand: Snapper Pages: 16

LT180H331BV series I

Brand: Snapper Pages: 176

Brand: Snapper Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands