Toro 74942TE Operator'S Manual Download Page 16 | Manualshive

Page: 16 / 72

background image

Blade-control Switch (PTO)

The blade-control switch (PTO) is used to engage the electric
clutch and drive the mower blades. Pull the switch up to
engage the blades and release. To disengage the blades,
push the blade-control switch (PTO) down or move a
motion-control lever into the neutral-lock position.

Ignition Switch

This switch starts the engine and has 3 positions:

Start, Run,

and

Off

.

Motion-control Levers

Use the motion-control levers to drive the machine forward,
reverse, and turn either direction.

Neutral-lock Position

The neutral-lock position is used with the safety-interlock
system and to determine neutral position.

Fuel-shutoff Valve

Close the fuel-shutoff valve (under the seat) when
transporting or storing the machine.

Attachments/Accessories

A selection of Toro approved attachments and accessories is
available for use with the machine to enhance and expand
its capabilities. Contact your Authorized Service Dealer or
Distributor or go to www.Toro.com for a list of all approved
attachments and accessories.

Specifications

Note:

Specifications and design are subject to change

without notice.

Width:

152 cm (60 inch) Deck

Without Mower Deck

134.6 cm (53.0 inches)

With Mower Deck

168.4 cm (66.3 inches)

Length:

152 cm (60 inch) Deck

Roll Bar—Up

221.6 cm (87.25 inches)

Roll Bar—Down

226.0 cm (88.95 inches)

Height:

Roll Bar—Up

Roll Bar—Down

179.1 cm (70.5 inches)

118.9 cm (46.8 inches)

Weight:

Model

Weight

60 inch Mower Decks

590 kg (1301 lb)

16

«
...
14
15
16
17
18
...
»

Summary of Contents for 74942TE









































































Reviews:

No comments

Related manuals for 74942TE

Brand: Snapper Pages: 1

Brand: SANLI Pages: 16

Brand: MTD Pages: 6

Brand: Qualcast Pages: 24

Brand: Dixon Pages: 48

36V UltraStore 340R

Brand: Flymo Pages: 14

Brand: Toro Pages: 4

Brand: AL-KO Pages: 25

Stockman 4000 A16314E

Brand: COX Pages: 50

Brand: Baroness Pages: 93

Brand: Yazoo/Kees Pages: 46

Brand: Cub Cadet Pages: 34

Brand: Craftsman Pages: 48

Brand: Craftsman Pages: 30

Brand: Craftsman Pages: 30

Brand: Craftsman Pages: 28

Brand: Craftsman Pages: 56

Brand: Craftsman Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands