Toro 74942TE Operator'S Manual Download Page 12

Page: 12 / 72

117-3888

Sliding, tipping hazard—do not use the machine near
drop-offs with slopes greater than 15 degrees, use the
machine a safe distance from drop-offs on slopes less than
15 degrees; do not turn sharply while traveling fast, drive
slowly when turning.

Warning—do not use dual ramps, use one piece ramps
when transporting machine; do not use ramps with
inclination greater than 10 degrees.

120-5897

Choke

Slow

Fast

Power take-off (PTO),
Blade control switch

Continuous variable
setting

125-9384

Read the

Operator's

Manual

for information on

lubricating the idler-pulley
pivots.

Counter clockwise rotation

Lubricate the spindles
every 50 operating hours.

Clockwise rotation

127-6651

Read the

Operator's

Manual

Remove the key from
the ignition and read the

Operator's Manual

before

performing maintenance.

Height-of-cut

Summary of Contents for 74942TE









































































Search results

Summary of Contents for 74942TE

Reviews:

Related manuals for 74942TE

Brands by name

Popular brands

Toro 74942TE, Operator'S Manual

Search results

Summary of Contents for 74942TE

Reviews:

Related manuals for 74942TE

Brands by name

Popular brands