background image

Toro General Commercial Products Warranty

 

A Two-Year Limited Warranty

Conditions and Products Covered

The Toro Company and its affi liate, Toro Warranty Company, 
pursuant to an agreement between them, jointly warrant your Toro 
Commercial Product (“Product”) to be free from defects in materi-
als or workmanship for two years or 1500 operational hours*, 
whichever occurs fi rst. This warranty is applicable to all products 
with the exception of Aerators (refer to separate warranty state-
ments for these products). Where a warrantable condition exists, 
we will repair the Product at no cost to you including diagnosis, 
labor, parts, and transportation. This warranty begins on the date 
the Product is delivered to the original retail purchaser.

* Product equipped with hour meter

Instructions for Obtaining Warranty Service

You are responsible for notifying the Commercial Products Dis-
tributor or Authorized Commercial Products Dealer from whom 
you purchased the Product as soon as you believe a warrantable 
condition exists. If you need help locating a Commercial Products 
Distributor or Authorized Dealer, or if you have questions regard-
ing your warranty rights or responsibilities, you may contact us at:

 

Toro Commercial Products Service Department

 

Toro Warranty Company

 

8111 Lyndale Avenue South

 

Bloomington, MN 55420-1196

 952-888-8801
 E-mail: 

[email protected]

Owner Responsibilities

As the Product owner, you are responsible for required main-
tenance and adjustments stated in your 

Operator’s Manual

Failure to perform required maintenance and adjustments can be 
grounds for disallowing a warranty claim.

Items and Conditions Not Covered

Not all product failures or malfunctions that occur during the 
warranty period are defects in materials or workmanship. This 
warranty does not cover the following:

Product failures which result from the use of non-Toro 
replacement parts, or from installation and use of add-on, 
or modifi ed non-Toro branded accessories and products. A 
separate warranty may be provided by the manufacturer of 
these items.
Product failures which result from failure to perform recom-
mended maintenance and/or adjustments. Failure to properly 
maintain your Toro product per the Recommended Mainte-
nance listed in the 

Operator’s Manual

 can result in claims for 

warranty being denied.
Product failures which result from operating the Product in an 
abusive, negligent or reckless manner.
Parts subject to consumption through use unless found to be 
defective. Examples of parts which are consumed, or used 
up, during normal Product operation include, but are not lim-
ited to, brakes pads and linings, clutch linings, blades, reels, 
bed knives, tines, spark plugs, castor wheels, tires, fi lters, 
belts, and certain sprayer components such as diaphragms, 
nozzles, and check valves, etc.
Failures caused by outside infl uence. Items considered to be 
outside infl uence include, but are not limited to, weather, stor-
age practices, contamination, use of unapproved coolants,

lubricants, additives, fertilizers, water, or chemicals, etc.
Normal noise, vibration, wear and tear, and deterioration.
Normal “wear and tear” includes, but is not limited to, dam-
age to seats due to wear or abrasion, worn painted surfaces, 
scratched decals or windows, etc.

 

Parts

Parts scheduled for replacement as required maintenance are war-
ranted for the period of time up to the scheduled replacement time 
for that part. Parts replaced under this warranty are covered for the 
duration of the original product warranty and become the property 
of Toro. Toro will make the fi nal decision whether to repair any ex-
isting part or assembly or replace it. Toro may use remanufactured 
parts for warranty repairs.

Note Regarding Deep Cycle Battery Warranty:

Deep cycle batteries have a specifi ed total number of kilowatt-
hours they can deliver during their lifetime. Operating, recharging, 
and maintenance techniques can extend or reduce total battery 
life. As the batteries in this product are consumed, the amount 
of useful work between charging intervals will slowly decrease 
until the battery is completely worn out. Replacement of worn out 
batteries, due to normal consumption, is the responsibility of the 
product owner. Battery replacement may be required during the 
normal product warranty period at owner’s expense.

Maintenance is at Owner’s Expense

Engine tune-up, lubrication cleaning and polishing, replacement of 
fi lters, coolant, and completing Recommended Maintenance are 
some of the normal services Toro products require that are at the 
owner’s expense.

General Conditions

Repair by an Authorized Toro Distributor or Dealer is your sole 
remedy under this warranty.

Neither The Toro Company nor Toro Warranty Company is
liable for indirect, incidental or consequential damages in
connection with the use of the Toro Products covered by this 
warranty, including any cost or expense of providing sub-
stitute equipment or service during reasonable periods of 
malfunction or non-use pending completion of repairs under 
this warranty. Except for the Emissions warranty referenced 
below, if applicable, there is no other express warranty. All 
implied warranties of merchantability and fi tness for use are 
limited to the duration of this express warranty.

Some states do not allow exclusions of incidental or consequential 
damages, or limitations on how long an implied warranty lasts, so 
the above exclusions and limitations may not apply to you. This 
warranty gives you specifi c legal rights, and you may also have 
other rights which vary from state to state.

Note regarding engine warranty:

The Emissions Control System on your Product may be covered 
by a separate warranty meeting requirements established by the 
U.S. Environmental Protection Agency (EPA) and/or the California 
Air Resources Board (CARB). The hour limitations set forth above 
do not apply to the Emissions Control System Warranty. Refer to 
the Engine Emission Control Warranty Statement printed in your 

Operator’s Manual

  or contained in the engine manufacturer’s 

documentation for details.


 

Countries Other than the United States or Canada

Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) 
to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfi ed with your Distributor’s service or 
have diffi culty obtaining guarantee information, contact the Toro importer.

Part No. 374-0031 Rev. D

Summary of Contents for 41253 Series









Reviews: