background image

Figure 14

1.

Choke lever

3. Firmly push in the primer 3 times with your thumb,

holding the primer in a for a second before releasing
it each time (Figure 15 and Figure 16).

Figure 15

Figure 16

1.

Symbols on the choke lever indicating to move the choke
lever to the left to activate the choke.

Note:

Remove your glove when you push in the

primer so that air cannot escape from the primer
hole.

Important:

Do not use the primer or the choke

if the engine has been running and is hot.
Excessive priming may flood the engine and
prevent it from starting.

4. Connect an extension cord to a power source and

the machine, and push the electric-start button
(model 38569 only) (Figure 17), or pull the recoil
start handle (Figure 18).

Figure 17

Note:

Use only a UL-listed, 16-gauge extension

cord recommended for outdoor use that is not
longer than 50 feet (15 m).

WARNING

The electrical cord can become damaged,
causing a shock or fire.

Thoroughly inspect the electrical cord before
plugging it into a power source. If the
cord is damaged, do not use it to start the
machine. Replace or repair the damaged cord
immediately. Contact an Authorized Service
Dealer for assistance.

10

Summary of Contents for 38567

























Reviews: