Toro 34231 Operator'S Manual Download Page 63

Page: 63 / 84

Servicing the Fuses

The electrical system is protected by fuses. If a fuse
opens, check the component or circuit for a load or
short.

Circuit protected

Fuse size

Location

Main power

10 A

Between the
ignition switch and
start solenoid.

Sprayer

30 A

Between the start
solenoid and
spray-pump relay.

Display

1 A

Between the
ignition switch
and sprayer and
information display.

Remove the negative battery cable from the
battery; refer to step

Removing the Battery

(page 61)

Note:

Ensure that the negative battery cable

does not touch the battery terminal.

Rotate open the right spray tank; refer to

Opening the Tanks (page 50)

Open the cover of the fuse holder (

Figure 87

g313063

Figure 87

Fuse holder—10 A fuse
(main power)

Fuse holder—30 A fuse
(spray pump)

Fuse holder—1 A fuse
(display)

Pull the fuse from the socket of the fuse holder
(

Figure 87

Install a fuse of the same type into the socket of
the fuse holder (

Figure 87

Close the cover onto the fuse holder until the
cover latches securely (

Figure 87

Close and secure the right spray tank; refer to

Closing the Tanks (page 51)

Install the negative battery cable to the battery
terminal, and install the battery cover; refer to
steps

Installing the Battery (page 61)

Summary of Contents for 34231





















































































Search results

Summary of Contents for 34231

Reviews:

Related manuals for 34231

Brands by name

Popular brands

Toro 34231, Operator'S Manual

Search results

Summary of Contents for 34231

Reviews:

Related manuals for 34231

Brands by name

Popular brands