Toro 139-6655 Installation Instructions Manual Download Page 1

Form No. 3447-975 Rev A

60in or 72in Recycler

®

Kit

Model No. 139-6655

Model No. 139-6659

Installation Instructions

Important:

This kit does not come with the recycler blades.

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure

Description

Qty.

Use

1

No parts required

Raise the mower for access
(GrandStand mowers only).

2

No parts required

Prepare the machine.

3

No parts required

Remove the existing baffles (for mower
decks with existing baffles).

4

No parts required

Remove the deck fasteners and
discharge baffle (for Z Master 4000
mower deck).

5

No parts required

Remove the existing discharge chute.

6

No parts required

Drill holes (for G3 mower decks).

Discharge plate

1

Cover plate

1

Carriage bolt (3/8 x 1-1/4 inches)

2

Carriage bolt (5/16 x 7/8 inch)

1

Small flange nut (3/8 inch)

2

Flange nut (5/16 inch)

1

Large flange nut (3/8 inch)

2

7

Carriage bolt (3/8 x 1 inch)

2

Install the discharge plate.

Left baffle

1

Center baffle

1

Right baffle

1

Small flange nut (3/8 inch)

7

Carriage bolt (3/8 x 1 inch)

6

Bolt (3/8 x 1 inch)

2

8

Large flange nut (3/8 inch)

1

Install the baffles.

Kickers

2

Carriage bolt (5/16 x 7/8 inch)

4

9

Locknut (5/16 inch)

4

Install the kickers (for 72-inch mower
decks).

10

No parts required

Tighten all the fasteners.

11

Recycler blade (sold separately)

3

Install the recycler blades.

© 2021—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3447-975*

 

Summary of Contents for 139-6655













Reviews: