background image

Declaration of Incorporation

The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s)
conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain
Toro models as indicated on the relevant Declarations of Conformity.

Model No.

Serial No.

Product Description

Invoice Description

General Description

Directive

03655

CrossTrax All-Wheel Drive Kit

CROSSTRAX AWD KIT

[F15 AND NEWER]

CrossTrax All-Wheel Drive Kit

2006/42/EC,

2000/14/EC

Relevant technical documentation has been compiled as required per Part B of Annex VII of 2006/42/EC.

We will undertake to transmit, in response to requests by national authorities, relevant information on this partly
completed machinery. The method of transmission shall be electronic transmittal.

This machinery shall not be put into service until incorporated into approved Toro models as indicated on the
associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in
conformity with all relevant Directives.

Certified:

EU Technical Contact:

Peter Tetteroo
Toro Europe NV
B-2260 Oevel-Westerloo
Belgium

David Klis

Tel. 0032 14 562960

Sr. Engineering Manager

Fax 0032 14 581911

8111 Lyndale Ave. South
Bloomington, MN 55420, USA
September 26, 2013

12

 

Summary of Contents for 03655













Reviews: