background image

Form No. 3385-758 Rev B

CrossTrax All-Wheel Drive Kit

2015 and After Reelmaster

®

5010 Series Traction Unit

Model No. 03655

Installation Instructions

Note:

This kit, when installed to Reelmaster 5010 series Traction Units, is covered by Patent # 7,017,703.

WARNING

Bodily injury could occur if the traction unit rolls over.

When operating machine, always use the seat belt and ROPS together.

Safety

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential
danger. Replace any decal that is damaged or lost.

110-8869

1.

Warning—read the

Operator's Manual

, do not operate this

machine unless you are trained.

2.

Thrown object hazard—keep bystanders a safe distance
from the machine.

3.

Tipping hazard—slow machine before turning, do not turn
at high speeds; lower the cutting unit when driving down
slopes; use a roll over protection system and wear the seat
belt. Always wear a seat belt when a ROPS is in place.

4.

Warning—do not park the machine on slopes; engage the
parking brake, lower the cutting decks, stop the engine and
remove the ignition key before leaving the machine.

5.

Warning—read the

Operator's Manual

, do not tow the

machine.

110-8973

(Affix over part no. 110–8869 for CE*)

* This safety decal includes a slope warning required on the machine for

compliance to the European Lawn Mower Safety Standard EN836:1997. The

conservative maximum slope angles indicated for operation of this machine are

prescribed by and required by this standard.

1.

Warning—read the

Operator's Manual

, do not operate this

machine unless you are trained.

2.

Thrown object hazard—keep bystanders a safe distance
from the machine.

3.

Tipping hazard—do not operate on slopes greater than 15°;
lower the cutting decks when operating on slopes; wear
the safety belt.

4.

Warning—do not park the machine on slopes; engage the
parking brake, lower the cutting decks, stop the engine and
remove the ignition key before leaving the machine

5.

Warning—read the

Operator's Manual

before towing the

machine.

© 2014—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA.

All Rights Reserved

*3385-758* B

 

Summary of Contents for 03655













Reviews: