background image

INTRODUCTION 

Thank you for choosing Tornado Industrial Vacuum Cleaner, a high-quality product 

based on the newest state-of-the-art technology. We hope that this device will be 

to your satisfaction and meet your expectations. We are continuously striving to 

improve our products in our product segment and will continue to supply the 

market with new equipment. 

 

 

 

NOTICE! 

1.These instructions are only for TIV2000 Dust Extractors. 

 

2.  TIV2000  Dust Extractors are designed to clean construction areas and be connected to 

small and medium machines such as drills, grinders etc. The machine is suitable for picking up 

dry, non-flammable dust and debris in and indoor environment. It is not suitable for picking up 

liquids. 

   

3. Please pay particular attention to the safety regulations and safety instructions 

 

4. Read the complete instruction manual before using. 

 

5. All spare parts and accessories used with this device must be those specified by Tornado. 

 

6. Check before and after use that all the switches are in OFF position.   

 

Environmental protection   

The packaging material can be recycled. Please do not throw the packaging material into 

household waste; please send it for recycling. 

 

Old devices contain valuable materials that can be recycled; these should be sent for 

recycling. Batteries, oil, and similar substances must not enter the environment. Please dispose 

of your old devices using appropriate collection systems. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for TIV2000
















Reviews: