manualshive.com logo in svg

Tornado ORBITER, User Manual

Share
Download
Tornado ORBITER User Manual Download Page 26

Tornado International Ltd

Ver 3.1 Jan 14

ORBITER MANUAL

6.13    EVERY SIX MONTHS OF OPERATION:

Perform all of the Weekly Checks and in addition:

a) Remove the main wheels from the ORBITER, remove the roller bearing and 

thoroughly clean. Clean the axle, re-assemble and grease (proceed as per Chapter 7.4.)

b) Remove the castors and remove the castor wheel axle. Thoroughly clean, re-assemble 

and re-grease. Proceed as per Chapters 7.6 & 7.7.

c)

If seat belts are fitted -

 perform an operational and visual check of the seat belts as in 

chapter 6.12. Consider their replacement. In any event the seat belt should be 
replaced after 12 months of operation.

6.14    BEFORE STORAGE:

Perform the weekly check and six-month service and in addition:

a) Note any parts required and order them from Tornado International NOW!
b) Thoroughly clean the body and chassis.
c) Apply a good polish to the body and treat any damaged paint on the chassis.
d) Deflate the bumper to 0.25 bar.
e) Ensure that the batteries are removed from the ORBITER.
f) Store the ORBITER in a dry well ventilated place. Cover with clean sheets. Do not use

the overnight covers for extended storage.

g) Store the batteries in a FROST-FREE place. It is vital to charge the batteries for 

24HRS EACH MONTH OF STORAGE. Failure to observe these two precautions will
result in premature battery failure.

6.15    TO RETURN TO SERVICE:

a) Remove the ORBITERS from storage and thoroughly clean.
b)

Carefully check the bumper for any signs of cracking or damage.

c) Using a car tyre foot pump inflate the bumper to your normal pressure but in no case 

above 1bar.

d)

Carry out the weekly check and test each ORBITER in turn

.

1N00-962

Page 26

 Tornado International Ltd 2014

Summary of Contents for ORBITER







































Reviews:

No comments

Brands by name

Popular brands

Load more brands