manualshive.com logo in svg

Tornado ORBITER, User Manual

Share
Download
Tornado ORBITER User Manual Download Page 20

Tornado International Ltd

Ver 3.1 Jan 14

ORBITER MANUAL

When fitting and removing the batteries handle them with care. Avoid dropping them into
the ORBITER or onto the floor. Dropping the battery will cause the plates to deform with
the result that some cells will become useless. Do not allow the ORBITER to be used with
discharged batteries. Customer satisfaction will be reduced as will the battery life. Charge
the batteries or remove the ORBITER from service as soon as the vehicle speed is visibly
reduced. Do not part charge and re-use the batteries as this will lead to premature failure.

5.5    Storage

If the ORBITERS are to be removed from service the correct storage of the batteries is
vital.   As   soon   as   the   batteries   are   removed   from   service   they   should   be   charged   for
24hours. They should then be stored in a FROST-FREE place and be charged for 24hours
each   month   of   storage.   Failure   to   follow   these   instructions   will   result   in   permanent
damage to the batteries.

5.6    Summary

1. Only use the chargers supplied.
2. Charge the batteries at the end of each operating period.
3. Do not allow repeated undercharging.
4. Remove batteries from service before they are completely discharged and recharge 

immediately.

5. Charge for 24hours before storage and recharge for 24hours for each month of storage.
6. Store in a FROST-FREE place.
7. Handle the batteries with care.
8. Keep the terminals and plug clean.
9. Do not remove the vents, or add water to the cells.

The batteries are expensive. It pays to look after them!

1N00-962

Page 20

 Tornado International Ltd 2014

Summary of Contents for ORBITER







































Reviews:

No comments

Brands by name

Popular brands

Load more brands