4
I
NTRODUCTORY COMMENT
Thank you for selecting our machine.
This floor cleaning machine is used for
the commercial cleaning of most types
of hard floors. During forward move
-
ment, the combined action of the brush
and the detergent solution remove the
dirt which, is recovered through the rear
squeegee assembly, giving a perfectly
dry surface.
The machine must be used only for this
purpose. It gives the best performance
if it is used correctly and maintained in
good condition. Read this instruction
booklet carefully prior to using this ma-
chine and whenever difficulties arise in
the course of the machine’s use. Con-
tact our service department for all advice
and servicing as may prove necessary.
GENERAL RULES OF SAFETY
The rules below must be followed care
-
fully in order to avoid injury to the opera-
tor and damage to the machine.
- Read the labels on the machine care-
fully. Do not cover them for any reason
and replace them immediately if dam-
aged.
- The machine must be used only by au-
thorized staff that have been instructed
on its correct and proper use.
- When operating the unit, pay attention
to other people and especially to chil-
dren.
- Do not allow the machine to be used
as a toy.
- The machine is not to be used by per-
sons, with reduced physical, sensorial
or mental capabilities, or with lack of
experience and/or knowledge.
- The outlet for the charger must be
equipped with a standard electrical
ground system.
- Do not allow the cord to become dam
-
aged.
- Do not mix different detergents.,
- Storage temperature: between 32°F
(0°C) and 131°F (+55°C).
- Operating temperature: between 32°F
(0°C) and 104°F (+40°C).
- Place appropriate signs in and around
the cleaning area.
- If the machine does not work properly,
check by conducting simple mainte-
nance procedures. Otherwise, ask for
technical advice from an authorized
service center.
- Where parts are required, ask for
ORIGINAL spare parts from the distribu-
tor and/or from an authorized dealer.
- Use only ORIGINAL brushes indicated
in the paragraph “RECOMMENDED
BRUSHES".
- For any cleaning and/or maintenance
operation remove the power from the
machine.
- Do not take off the protections which
require the use of tools for their removal.
- Do not wash the machine with direct
water jets or with high water pressure
nor with corrosive material.
- Every 200 working hours have a ma-
chine check by an authorized service
technician.
- Before using the machine, check that
all panels and coverings are in their
position as indicated in this use and
maintenance manual.
Symbol denoting the charge
level of the batteries.
Symbol that indicates the posi-
tion of the drain plug of the solution tank.
This symbol indicates
that the tanks are to be emptied before
rotating the machine.
Indication of the maximum tem-
perature of the solution detergent.
Symbol that indicates the flow
adjuster of the detergent solution.
Symbol denoting the crossed
bin. Indicates that at the end of its activ-
ity, the machine has to be disposed
conforming to the laws in force.
Symbol denoting the open book.
Indicates that the operator has to read
the manual before the use of the ma-
chine.
- The humidity should not exceed 95%.
- Do not use the machine in explosive
atmosphere.
- Do not use the machine as a means of
transport.
- Do not use the machine onstairs.
- Do not use acid solutions which could
damage the machine.
- To avoid damage to the floor, do not
allow the brush to rotate while the
machine is in one place.The machine
muust be moving while the brush is
rotating.
- Do not use the machine on surfaces
covered with inflammable liquids or
dusts (for example hydrocarbons, ashes
or soot).
- In case of fire, use a powder based fire
extinguisher. Do not use water.
- Do not strike structures where there is
a danger of falling objects.
- Do not use the machine on areas hav-
ing a higher gradient than the one stated
on the number plate.
- Restore all electrical connections after
any maintenance operation.
- Provide for the scrapping of the mate-
rial of normal wear (brushes, squeegee
blades etc.) following strictly the respec
-
tive rules.
- When your machine has stopped
functioning, provide for the appropri-
ate waste disposal of its materials,
especially oils, batteries and electronic
components, and considering that the
machine itself has been, where possible,
constructed using recyclable materials.
SYMBOLOGY
Symbol 0/1 indicating the ON/
OFF switch and its signal lamp.
Symbol denoting the solution
valve. Indicates the switch and
the signal lamp of the solenoid valve.
Symbol denoting the brush.
Indicates the switch and the signal lamp
of the brush motor.
Symbol denoting the suction
motor. Indicates the switch and the
signal lamp of the suction motor.
Summary of Contents for 99617
Page 3: ...3 NOTES...