TORCHVIEW CDVR-0402U User Manual Download

Page: 22 / 41

- 22 -

3.5. Sensor Setup

CATEGORY DEFAULT

ADJUSTMENT

SENSOR
NO.

Set the SENSOR Number.

[Left, Down] : Decrease Number
[Right, Up] : Increase Number

SENSOR
TYPE

Select the SENSOR TYPE

[Up, Down, Left, Right] : Select NO or NC

CAMERA
LINK

Select the CAMERA that is to be connected to the SENSOR

[Left, Down, Right, Up] : Move between channels

[ENTER] : Toggle to Enable/Disable

ALARM
LINK

Select the ALARM OUTPUT that will be connected to the SENSOR

[Left, Down, Right, Up] : Move between channels
[ENTER] : Toggle to Enable/Disable

OPERATION
TIME

0~24

Set the OPERATION TIME for the selected sensor. (Start Hour ~ End Hour)
It will not activate if same time is set.

Range : 0~24(Hour), OFF
[Left, Right] : Move between Start ~ End
[Up, Down] : Increase/Decrease hour.
Number keys can also be used to change the hour.

OPERATION
MODE

SPOT

Set whether to show the camera view in full screen on the Spot monitor when
the sensor is triggered.

[NORMAL] : Disable
[SPOT] : Apply

If a sensor is linked to several channels, the channels will be displayed in the
multi-screen mode.

[Up, Down, Left, Right]: Move between NORMAL

SPOT

RECORDING
DWELL TIME

Set the time duration for which the camera will continue recording when the
sensor is triggered.
Input Range : 0~600(Second)

[Left, Down] : Decrease dwell time
[Right, Up] : Increase dwell time
Number keys can also be used to change the dwell time.

Configuration

Summary of Contents for CDVR-0402U










































Search results

Summary of Contents for CDVR-0402U

Reviews:

Related manuals for CDVR-0402U

Brands by name

Popular brands

TORCHVIEW CDVR-0402U, User Manual

Search results

Summary of Contents for CDVR-0402U

Reviews:

Related manuals for CDVR-0402U

Brands by name

Popular brands