background image

TOPAZ Uno Plus
RIGGING INSTRUCTIONS

CONTENTS

2. Introduction
2. Manufacturers Details
3. Maintenance
4-5. Mast and Mainsail
6-8. Boom
9-10. Jib
11. Rudder

INTRODUCTION

These RIGGING  INSTRUCTIONS have been compiled to help you to rig your TOPAZ  UNO  PLUS sailing dinghy.

Please also ensure that you refer to your TOPAZ  OWNERS MANUAL. The OWNERS MANUAL has been compiled 
to help you to operate your craft with safety and enjoyment. It contains details of the craft, the equipment supplied 
or fitted, it’s systems and information on its operation and maintenance. Please read it carefully and familiarise yourself
with the craft before using it.

If this is your first craft, or you are changing to a type of craft you are not familiar with, for your own comfort and safety,
please ensure that you obtain handling and operating experience before assuming command of the craft. Your dealer 
or national sailing federation or yacht club will be pleased to advise you of local sea schools, or competent instructors.

PLEASE KEEP THE RIGGING  INSTRUCTIONS and THE OWNERS MANUAL IN A SECURE PLACE AND HAND THEM
OVER TO THE NEW OWNER WHEN YOU SELL THE CRAFT.

MANUFACTURER  DETAILS

For further information, spares and accessories, please contact the manufacturer:
Topper International Ltd 
Kingsnorth Technology Park
Wotton Road
Ashford
Kent TN23 6LN
Tel44 (0) 1233 629186
Fax +44 (0) 1233 645897
email [email protected]

2

Summary of Contents for Uno Plus













Reviews: