3
To stop duplex mode, select desired channel, press and hold the # key on
the keypad for 4 seconds until you will see the “
+
” disappear
from the
analogue status bar. This notes the current channel is not in duplex mode
and will transmit/receive on the current channel.
Squelch
The radio audio can open at varying levels of received signal strength.
1.
Short press ≡ (menu) key
2.
Short press
⯅
key three times
and short press ≡ key to display
analogue Settings
3.
Short press
⯆
key three times and short press
≡
key to display
SQL Settings
4.
Short press
⯅
or
⯆
keys to change between desired levels of
squelch
5.
Short press ≡ key to save configuration
Note. Higher the number for the squelch setting the stronger the signal
strength is required for receiving of transmissions.
BCLO
Busy Channel Lock Out is used to stop the use of the PTT if the radio is
receiving a UHF transmission.
1.
Short press ≡ (menu) key
2.
Short press
⯅
key three times
and short press ≡ key to display
analogue Settings
3.
Short press
⯆
key eight times and short press
≡ key to display
BCLO Settings
4.
Short press
⯅
or
⯆
keys to change between desired settings
5.
Short
press ≡ key to save configuration
Note. Once enabled transmitting from the radio will be disable while the
radio is receiving a transmission and will only enable again after the radio
has stopped receiving a transmission.
Scan
The radio can scan through selected channels looking for transmission on
the channel, the scan will scan through channels inside the scan group. A
Star displayed in the status bar, notes if the current channel is in the scan
group. To scan through the scan group press and hold the * key on the
keypad for 2 seconds. Pressing the * key again will stop the scan and revert
to the original channel the scan was commenced from. If the radio stops on
a busy channel, pushing the PTT will stop the radio from scanning and place
the radio on the channel currently stopped. To add/remove channels to the
scan group find a channel that is not in the scan group, noted by the Star in
the status bar.
1.
Short press ≡ (menu) key
2.
Short press
⯅
key three times
and short press ≡ key to display
Analogue Settings
3.
Short press
⯅
key three times
and short press ≡ key to display
Scan. Add
4.
Short press ≡ key to add channel to the scan group
When you add the channel to the scan group a Star will now be displayed in
the status bar. This indicates current channel is in the scan group.
Note. Removing a channel from the scan group is the same process but
selecting delete when in Scan. Add Settings.
CTCSS
To activate Continuous Tone-Coded Squelch System, select desired channel.
1.
Short press ≡ (menu) key
2.
Short press
⯅
key three times
and short press ≡ key to display
Analogue Settings
3.
Short press
⯅
key five times
and short press ≡ key to display
RX.
CDC
4.
Short press
⯅
or
⯆
keys to select desired configuration
5.
Short press ≡ key to s
ave configuration
Note. The same procedure is used to select TX CTCSS by selecting TX. CDC.
In the Analogue Settings menu.
Store Channel for Receive Only
You can store any channel from 400MHz to 480MHz as a receive only
channel in memory locations 121 to 199. These can also be added to the
scan group.
1.
In analogue mode short press *, this enables frequency display
2.
Key in a frequency between 400Mhz and 480Mhz
3.
Short press ≡ (menu) key
4.
Short press
⯅
key three times and short press ≡ key to display
Analogue Settings
5.
Short press
⯆
key once and short press ≡ key to display Storage
Channel
6.
Key in a channel number between 121
–
199 and short press ≡
key to save configuration
Note. These channels are receive only channels.
ADVANCED SETTINGS
SOS
Mode
The unit has an SOS alert feature that if held for 3 seconds will send an alert
message to all other users. This feature can be disabled/enabled;
1.
Short press ≡ (menu) key
2.
Short press
⯅
key
twice and short press ≡ key to display ADV
Settings
3.
Short press
⯅
key six
times and short press ≡ key to display SOS
Settings
4.
Short press
⯅
or
⯆
keys to change between desired settings
5.
Short press ≡ key to save configuration
Note. HOT MIC mode opens the Tx. for 10 seconds when the SOS alert is
triggered. Disabling the SOS mode for the unit will not prevent the unit
from receiving SOS alerts, if you would like this feature completely removed
please contact your local dealer.
PTT Records
The unit can record all the audio the unit is receiving. To listen to these
recordings;
1.
Short press ≡ (menu) key
2.
Short press
⯆
key four
times and short press ≡ to display PTT
Records list
3.
Short press
⯅
or
⯆
keys to change between desired recording
4.
Sho
rt press ≡ key to play recording
Note. The recording function needs to be enabled to listen to recordings
this function can be enabled/disabled under Settings > Record Control
LCD Display Reversal
The LCD display can be inversed if the unit is mounted upside down to
change LCD display;
1.
Short press ≡ key
2.
Short press
⯅
key twice and short press
≡ key
to select ADV
Settings
3.
Short press
⯆
key eight times and short
press ≡ key to enter
Rotate Settings
4.
Short press
⯅
or
⯆
keys to select desired configuration
5.
Short press ≡ key to save configuration
Once inverse setting is selected and saved, the LCD display will reverse the
display. This setting can be undone by following above steps and selecting
the normal setting and saving.
Time
Zone
The radio can have the time displayed on the LCD adjusted to match local
time zone. These settings can be found under Settings > Time Zone.
Power On Mode
The unit can turn on via the accessory line or the power knob. These
settings can be found under ADV Settings > PWR ON MODE.
Power Off Mode
The unit can turn off via the accessory line or the power knob. These
settings can be found under ADV Settings > PWR OFF MODE.
Dual SIM
The unit can operate with two sim cards, adjusting the active sim card
settings can be found under ADV Settings > Dual SIM.