ToolPRO CMT18WD.9 Instruction Manual Download Page 6

Customer Helpline

 1300 889 028

6

Safety Information 

Important

 - Please read these instructions fully before starting assembly

Safety instruction for cutting

General Safety Warnings for your Battery Charger

Hold power tool by insulated gripping surfaces, when performing an operation where 
the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” 
wire may make exposed metal parts of the power tool “live” and could give the operator 
an electric shock.

WARNING

Read all safety warnings and all instructions. 

Failure to follow the 

warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

-   This appliance is not intended for use by persons (including children) with reduced 

physical, sensory or mental capabilities, or lack of experience and knowledge, unless 
they have been given supervision or instruction concerning use of the appliance by a 
person responsible for their safety. 

-   Children should be supervised to ensure that they do not play with the appliance.
  If the supply cord is damaged, it must be replaced by the manufacturer, its service 

agent or similarly qualified persons in order to avoid a hazard.

Additional safety instructions for your Battery Charger

1.  Before charging, read the instructions.
2.  For charge 1.5Ah/2.0Ah/4.0Ah battery pack only.
3.  Do not charge a leaking battery.
4.  Do not use chargers for works other than those for which they are designed.
5.  Before charging, ensure your charger is matching the local AC supply.
6.  The charging device must be protected from moisture.
7.  Do not use the charging device in the open.
8.  Do not short out the contacts of battery or charger.
9.  Respect the polarity “+/-“ when charging.
10. Do not open the unit and keep out of the reach of children. 
11. Do not charge the batteries of other manufactures or ill-suited models.
12. Ensure that the connection between the battery charger and battery is correctly 

positioned and is not obstructed by foreign bodies.

13. Keep battery charger’s slots are free of foreign objects and protect against dirt and 

humidity. Store in a dry and frost-free place.

14. When charging batteries, ensure that the battery charger is in a well-ventilated area 

d)  Under abusive conditions, liquid may be ejected from the battery; avoid contact.

 If 

contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek 
medical help. Liquid ejected from the battery may cause irritation or burns.

6) Service
  Have your power tool serviced by a qualified repair person using only identical 

replacement parts. 

This will ensure that the safety of the power tool is maintained.

General Power Tool Safety Warnings

Summary of Contents for CMT18WD.9





















Reviews: