This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming, or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE.
*1553631_v1_0917_02_IPL_m_en
Product overview
1
2
3
4
5
7
6
8
1 Trigger feed
2 Handle
3 Mains cable
4 Mains plug
5 Trigger
6 Stand bracket
7 Nozzle
8 Glue sticks
Operation
• Attach the stand bracket to the product.
• Put a glue stick (Ø11 mm) into the trigger feed. Press the trigger to advance the glue stick
into the feeding tube.
• Connect the mains plug to a standard mains socket. The product starts to heat up immediately.
• Let the product heat up for 5 minutes.
• Press the trigger to make the liquid adhesive exit the nozzle.
• Unplug the mains cable from the household power outlet after use.
Do not pull the glue stick out of the product. The remaining glue stick can remain in
the product once you have finished working.
Tips for glueing
•
The bonding surfaces must be free of dust and grease, and dry. Do not use flammable
detergents and solvents.
•
Zigzag lines of glue are good for glueing flexible materials (e.g. textiles).
Beads of glue are good for glueing all other materials.
• Press the trigger carefully and apply the adhesive to the parts to be glued. These parts can
be glued together within 15-20 seconds. If necessary, insert new glue sticks into the product.
• The bonding time is approximately 30 seconds and about 90 % of adhesion occurs after one
minute. The bonding time for thick beads of glue can be longer or shorter for small ones.
• Do not glue large areas at once, but work in sections. Apply the adhesive in a corrugated
pattern.
• You can increase adhesion by preheating the surfaces to be glued together, e.g. with a hot
air gun.
• Only remove adhesive residue when cold.
• You can loosen or adjust glued areas by heating them, e.g. with a hot air gun.
•
If you wish to glue two different materials together, first apply adhesive to the harder material.
•
The liquid adhesive can fill small holes and cracks.
Troubleshooting
Problem
Possible cause and solution
The product does not turn on.
Check to see if the plug is properly
connected to the wall outlet.
The mains cable or plug is defective.
Please contact the manufacturer.
The adhesive is not liquid enough.
The heating-up phase was too short. Let
the product heat up longer.
Care and cleaning
• Always disconnect the product from the power supply before cleaning it.
• Let the product cool down completely.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the casing or cause the product to malfunction.
• Use a dry, lint-free cloth to clean the product.
Disposal
Electronic devices are recyclable waste and must not be placed in household waste.
Always dispose of the product according to the relevant statutory regulations.
You thus fulfill your statutory obligations and contribute to the protection of the
environment.
Technical data
Operating voltage ......................... 220 – 240 V/AC, 50 Hz
Power consumption ...................... 25 W (operation), 100 W (heating)
Heating-up time ............................ 5 min
Melting temperature ...................... 170 °C
Cable length ................................. 1.4 m
Operating/storage conditions ........
0 to +35 °C, 20 – 99 % RH
Dimensions (L x W x H) ................ 190 x 34 x 168 mm
Weight .......................................... 250 g
