manualshive.com logo in svg

TONO Theta 7000, Instruction Manual

Share
Download
TONO Theta 7000 Instruction Manual Download Page 12

- 10 -

(12)  CW keying output terminal:

In CW mode, a CW keying terminal of a wireless set is connected
to this terminal.

(13)  KEY input terminal:

Key is connected to this terminal.

(14)  Power supply jack:

12 VDC or 5 VDC is put in.

(15)  SYNCM output jack:

Oscilloscope  is  connected  to  this  jack  in  mark-side  output  for
cross pattern.

(16)  SYNCS output jack:

Oscilloscope  is  connected  to  this  jack  in  space-side  output  for
cross pattern.

(17)  Hole for option switch mounting.

(18)  Fuse

3.3  Connector for a printer

Connector CN4 on the CPU board is a connector for a printer. The function of each pin is as fol-

lows. The fan-out of each pin is 1 standard TTL. Avoid overload!

1, 2, 3:

Leave  these  non-connected.  Take  care  not  to  make  these  in  contact  with  the
power  supply line or the ground line.

4:

Strobe: negative pulse with about 5 micro-sec width is put out with each output
of one character.

5 ~ 12:

Data: 5

th

 pin is LSB, 12

th

 pin is MSB.

13

GROUND

14, 15:

Leave these non-connected.

The CPU board can be taken out of the computer by the following procedure:

1. Remove eight M4 screws from the bottom of the computer.
2. Remove the bottom plate.
3. Remove M4 screws at the four corners of the CPU board.

4.  How to operate

4.1  Initialization

In case of operation miss, push the RESET switch in order to make the computer revert to the in-

itial state.

Summary of Contents for Theta 7000



























Reviews:

No comments

Brands by name

Popular brands

Load more brands