background image

- 9 -

(26)  

[

 | CH7]

 key:

Selects channel  7. When it is pushed with 

[SHIFT]

  key,  the  cur-

sor is made to advance for a single character.

(27) 

[WEIGHT | SPEED]

 key:

Sets the speed of transmitting and receiving of a message in CW,
BAUDOT and ASCII.

(28)  

[PAGE | CASE]

 key:

Change  the  CASE  either  LTR  or  FIG.  When  it  is  pushed  with

[SHIFT]

 key, page change on the displayed screen is made.

3.2

The back panel

Figure 5

(1)  PHONE jack:

Connects an earphone with the computer.

(2)  CW.BAUDOT input jack:

In  CW  or  BAUDOT  mode,  AF  output  of  a  wireless  set  (speaker
output terminal or earphone terminal) is connected to this jack.

(3)  ASCII input jack:

In  ASCII  mode,  AFSK  in  accordance  with  KCS  is  put  in  from  a
tape recorder or a microcomputer.

(4)  TTL IN jack:

In  CW,  BAUDOT  or  ASCII  mode,  non-modulated  signals  in  TTL
level are put in.

(5)  INPUT switch:

Makes the input selection. TTL or AF.

(6)  VHF output jack:

A terminal of a home  TV set is connected to this jack. Data are
displayed  in  CH1  and  CH2  resp.  CH3  and  CH4  in  European  TV
system.

(7)  VIDEO output jack:

Outputs  combined  video  signals. Monitor  TV  set  is  connected
with this jack.

(8)  AFSK output jack:

A  microphone  terminal  of  a  wireless  set  or  a  tape  recorder  is
connected with this jack.

(9)  AFSK GAIN volume:

Controls the AFSK output level.

(10)  TTL OUT jack:

Outputs in TTL level without modulation.

(11)  FSK keying output terminal:

In BAUDOT or ASCII mode, a RTTY keying terminal of a wire less
set and the like is connected to this terminal.

Summary of Contents for Theta 7000



























Reviews: