TonerRefillKits ReChargX RX180 Instructions Manual Download Page 5

Page: 5 / 10

TonerRefillKits.com

RechargX™ RX180 v2

Mon - Fri 8am - 5pm ET

2012.02.21

Page 5 of 10

Step 9: Clean the Area Around the Toner

Hopper Hole Before Sealing

Unfold the yellow/orange “toner grabber” cloth

from the ReChargX™ RX180 Premium Print Toner

Refill Kit and stretch it along both dimensions (it

will stretch considerably in one dimension and

not the other). Stretching the yellow/orange

toner grabber cloth activates the toner retaining

substance that is embedded within the cloth.

You will be using this cloth to clean the outside

of the toner hopper hole to ensure the leak-proof

seal will be applied firmly and securely to the

cartridge, as shown in figure 10.

NOTE:

Only use the toner grabber cloth on the

exterior of the toner cartridge around the toner

hopper hole area. Do not use the cloth to clean

any of the internal components or the cartridge

imaging drum.

Step 10: Seal the Toner Hopper Hole with

the ReChargX™ Leak-Proof Seal

Remove the protective backing from the

ReChargX™ leak-proof seal (figure 11) and

lower the seal around the toner hopper

hole.

Press firmly around the entire seal to

ensure the seal securely sticks to the toner

cartridge, as shown in figure 12.

Figure 10:

Cleaning the area around the toner hopper

hole before sealing

Figure 11:

Removing the ReChargX™ leak-proof seal

from the protective backing

Figure 12

: Toner hopper with ReChargX™ seal in place

Summary of Contents for ReChargX RX180











Search results

Summary of Contents for ReChargX RX180

Reviews:

Related manuals for ReChargX RX180

Brands by name

Popular brands

TonerRefillKits ReChargX RX180, Instructions Manual

Search results

Summary of Contents for ReChargX RX180

Reviews:

Related manuals for ReChargX RX180

Brands by name

Popular brands